2. If R₁ = R3 = 2k and R₂ = R₁ = 200kn, R₂ R₁ Uow Ry Uno w Consider the following difference amplifier circuit using an ideal op amp. Assume www.li RA + Vo to ground, and a low-frequency sine-Wave the a) Find the value of differential gain, Ad, in dB. What is the value of differential input resistance? (b) For R. I, what is the maximum possible lue of for which undistorted -) If the resistors have 1% tolerance (i.e., each can be within ±1% of its nominal value), find the worst-case common mode gain, Acm and the corresponding value of CMRR in dB.

2. If R₁ = R3 = 2k and R₂ = R₁ = 200kn, R₂ R₁ Uow Ry Uno w Consider the following difference amplifier circuit using an ideal op amp. Assume www.li RA + Vo to ground, and a low-frequency sine-Wave the a) Find the value of differential gain, Ad, in dB. What is the value of differential input resistance? (b) For R. I, what is the maximum possible lue of for which undistorted -) If the resistors have 1% tolerance (i.e., each can be within ±1% of its nominal value), find the worst-case common mode gain, Acm and the corresponding value of CMRR in dB.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit shown below, if the differential gain (Aa) of the op-amp is (50000) and the CMRR in (db) is (34). Find the output voltage (v_out). v_in1 = 10 mv V_out V_in2 = 1 mv GND1
The ideal op-amps depicted can swing rail-to-rail at output, and Vcc= 13 V. Initially, the output voltage Vo = +13 V and the input voltage is vS = -13 V. The feedback resistors are R1 = 6.4 k0, R2 = 8.5 kQ, and R3 = 1.6 KQ. If the input voltage is gradually increased, at what value of vS (to 1% accuracy) does the output voltage (Vo) change to Vo=-Vcc? VVV vS = + R10 Vcc -Vcc R20 04 O Vo
An op amp (20 dB drop in gain/decade), has an open-loop gain of 100 dB and a unity- gain frequency of 2 MHz. What is the open-loop bandwidth of the op amp?
A If an op-amp has a slew-rate of 5 V/us, find the Maximum bandwidth for a peak output voltage of: (a) 5 V, (b) 1.5 V, and (c) 0.4 V.
4. PD FB IN- 1 2 3 IN+ 4 8 VS+ 7 6 5 OUT NC VS- Using the Op-Amp diagram shown above, draw a line to create: 4.a. non-inverting amplifier 4.b. Inverting amplifier
A certain op-amp is used in a feedback configuration having a gain of 20 and a bandwidth of 500 kHz. a)If the external resistor values are changed to increase the gain to 40, what is the new bandwidth? The new bandwidth is 250khz What is the unity-gain bandwidth of the op-amp ??
6. Show the connection of two 741 op-amp stages to provide outputs that are 15 and -30 times larger than the input. Use a feedback resistor, Rf = 150 kQ, in all stages.
Vs RE www 2₁ www Rc1 11 Vcc RC2 Q₂ RF Q3 +₁ -O V₂ Sketch the feedback small signal model of this circuit.
I need the answer as soon as possible
A 741 OP-AMP has a gain-bandwidth product of 1 MHz. A non-inverting amplifier using this OP-AMP and having a voltage gain of 20 dB will exhibit a-3 dB bandwidth of a. 50 kHz b. 100 kHz C. 100/17 kHz d. 1000/7.07 kHz
For the circuit as shown, find:- A. Output at (V₁ = V₂ = 1volt)? B. Output at (V₁ = -V₂ = 1volt)? C. Ad = differential gain of the amplifier? D. Ac = common-mode gain of the amplifier? E. CMRR? 29. and respectively Answers -1 29 29 5 11 w 10 V20 B A Op-amp www 5 to Vo
How did they get case 1 and case 2 and simplify break down for a dummy?