Two plates each with thickness t = 16 mm are bolted together with 6– 22 mm diameter bolts forminga lap connection. Bolt spacing are as follows: S1 = 40 mm, S2 = 80 mm, S3 = 100 mm. Bolt holediameter = 25 mm. Using A36 steel having Fy = 248 MPa and Fu = 400 MPa.P►PS.SS2S2DETERMINE:1. Determine the ultimate load Pu that the connection can carry based on tensile rupture ofeffective net area using LRFD.2. If P = 200 kN, determine the maximum live load that the connection could carry based ontensile rupture using LRFD.P.

Answered: Image /qna-images/answer/92f4a465-777f-4e7d-ad20-6a0b86c5c1f0.jpg

Answered: 2. If P = 200 kN, determine the maximum…

Engineering

Civil Engineering

2. If P = 200 kN, determine the maximum live load that the connection could carry based on tensile rupture using LRFD.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The figure shows a roof truss and the detail of connection at joint B. The allowable stresses are 70…

Q: Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross…

Q: A 5.0 m high steel stanchion is fixed at the base and connected to a roof truss at the top. Design…

A: Design of battened column Assuming: fcd=0.5fy= 0.5×410 = 205 MPaArea required…

Q: Seven 7/8-in-diameter rivets fasten the plate to the fixed member. Determine the maximum and minimum…

Q: Determine the maximum resultant stress on the 20mm fillet weld. L1 = 200mm, L2 = 250mm & L3 =…

A: Answer:

Q: 10.7 The shearing force at a given section of a built-up I-girder is 1000 kN and the depth of the…

Q: what is the block shear rupture capacity of beam flange of the flange connection in kips? (2 decimal…

A: Tensile Strength: The Tensile strength of a material defines as the stress in tension that material…

Q: Draw SFD and BMD for the single side overhanging beam subjected to loading as shown below. Mark…

Q: The bracket is welded on one side of a steel column with 800mm of 6mm fillet weld. Determine the…

A: Given Data:Weld size = 800mm of 6mm fillet weldLoad = 44kNL=300mmH=200mm

Q: 1) Reqd: Determine Maximum Shearing Stresses for the 3 segments and 0at C 2) F (2)Solid…

Q: what is the block shear rupture capacity of beam flange of the flange connection in kips? (2 decimal…

A: Beam flangeW 16 x 50A992 steelA992 Fy = 50 ksi, Fu = 65 ksiEffective bolt hole diameter = bolt hole…

Q: Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross…

A: Given, A1 = 1.5 in2 dpin = 0.7 in a = 47 in b = 96 in

Q: The allowable shear stress for all pins is 15ksl. Determine the required dlameter for pln B.

Q: Problem 4 Determine the design tensile strength Pn of the MC18x58 channel shown based on yielding…

Q: 1. Identify zero force memeber. (Draw the FBD of Joint contain zero force member) B H|100 kN 60 kN K…

A: Identify the zero force member (Draw the FBD of joint contain zero force member).

Q: Help me find the answer to each question related to a truss. And write on a clean paper each, then…

Q: Draw the FBDS of all members -3.6 m- 2.7 m 2400 N B C D 2.7 m 1.5 m E 4.8 m-

A: We have to determine the FBD of the all members according to the given data in the question.

Q: Prove if the truss below is determinate, stable, or unstable. P is 3 Kips. Assume A and D as pin…

Q: Draw the FBD of the link 3 & 4. What is(are) the auxiliary equation(s)?

A: cy

Q: ties in column reinforcement is used to:

A: The term Tie is used to define the transverse reinforcement provided in column where the primary…

Q: B roller pin A fixed

A: Here a structure is given we need to verify wither its statically determinant or indeterminant For…

Q: Determine the LFRD design strength and the ASD allowable for the WF section shown connected by 4-020…

A: Determine the LFRD design strength and the ASD allowable for the WF section shown connected by 4-Ø20…

Q: Member-AB is_____. options: a two-force member a multi-force member a zero-force member…

A: Note :- According to Bartleby guidelines, Since you have posted a question with multiple sub-parts,…

Q: 50 3" 3" 3" 5" 3" 52" 12"

A: The centroid of the fastener group can be found by using a horizontal axis through the lower row…

Q: 10.8m 8.1m D ALANISH 100KN 130kN 150KN 160kN 140KN H 120kN 8 panels @ 6m ea. = 48m Determine the…

Q: Member BC in the truss below is a 300 mm wide, 10 mm thick steel plate attached to two other 12 mm…

A: Member BC: 300mm wide, 10mm plate attached to two 12mm plates at joint C, 3 A490 bolts, A36 plate

Q: The second level (framing plan below) of a reinforced concrete building used as light storage area…

A: Given: fc = 35 MPa fy= 415 MPa b = 300 mm h = 750 mm Slab-1 length 7.6 m Slab-1 width 3 m

Q: Can you please solve the calculations with equations and step by step and use space Gass software…

Q: Following is a simple tower truss. Propose a bolt connection design for member AC. You are to assume…

A: Bolted joints are a common feature in both construction and machine design. In contrast to riveted…

Q: For the two trusses shown, separately for problem (a) and (b), list all the zero-force members by…

Q: 1-102 Determine the intensity w of the maximum distrib- uted load that can be supported by the…

Q: what is the flexural rupture capacity of the shear plate of the shear connection in kips?

A: A36: Fy = 36 ksi, Fu = 58 ksieffective bolt hole diameter = bolt hole diameter + 1/16"bolt diameter…

Q: Problem # 6: The figure showsa rooftrussand the detail of connection at joint I. The allowable…

Q: L K H 3 m C ID E TF |-2 m -- 2 m--2 m-- 2 m--2 m --2 m- 20 kN 30 kN 40 kN

A: The stability of the truss is checked by the following formula; If m+r < 2j, The truss is…

Q: Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross…

Q: (i) Determine the rivet value of 20 mm diameter rivets connecting 10 mm plate and is in (a) single…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: Using method of section, Determine the force in members GF, GD, and CD of the truss. State if the…

A: Consider the figure,

Q: Design the diameter of the pin for the hinge support if the allowable shear stress is 250 Mpa. 1500…

Q: 2,300 mm A 1,150 mm 1,600 mm 75 kN

Q: A T-beam with bf-425mm, tf-100mm, bw=250mm, h-350mm, cc-30mm, stirrups 12mm is reinforced by 6-32mm…

A: Answer We are given Width of flange bf = 425 mm Thickness of flange tf = 100 mm Width of web bw =…

Q: Assuming k = 3000 lb/in², and considering only the bending stress: What rail type would you…

A: Given, Track modulus (k) = 3000 psi Force (P) = 30000 lb

Q: Please make a step by step procedure on how to calculate the maximum shearing stress experienced by…

A: Structural joints made by joining two or more pieces of metal together with welding techniques are…

Q: Date No. Cheek Deflection for Simply supported Girder Bridga :- Span L-20 DL from Section o.w weight…

A: To check the deflection for the simply supported girder bridge as described in the provided image,…

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

Two plates each with thickness t = 16 mm are bolted together with 6– 22 mm diameter bolts forming
a lap connection. Bolt spacing are as follows: S1 = 40 mm, S2 = 80 mm, S3 = 100 mm. Bolt hole
diameter = 25 mm. Using A36 steel having Fy = 248 MPa and Fu = 400 MPa.
P
►P
S.
S
S2
S2
DETERMINE:
1. Determine the ultimate load Pu that the connection can carry based on tensile rupture of
effective net area using LRFD.
2. If P = 200 kN, determine the maximum live load that the connection could carry based on
tensile rupture using LRFD.
P.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Design an unequal angle section to serve as a tie member of 1.6 m length in a roof truss. It has to carry an axial load of 118 kN. The gusset plate is connected to the longer leg of the angle. Also design the fillet weld. Permissible stress in weld = 108 N/mm² Permissible stress in axial tension = 150N / m * m ^ 2 Thickness (t), sectional area (A), weight/m run (w), distance of centres of gravity along x-axis and y-axis. cx and cy maximum and minimum radius of gyration f max and r min are given for some angles for design.
B Lsm +sm+sm-sm- Ax- Ra Rc- Ro= Hinge 90 kN/m 5m kN Ay KN kN kN Hinge -5m-5m KN
Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross sectional area of 1.00 in.² and a yield strength of 33 ksi. The pins at B, C, and D each have a diameter of 0.3 in. and an ultimate shear strength of 78 ksi. Each pin connection is a double-shear connection. Specifications call for a minimum factor of safety in member (1) of 1.3 with respect to its yield strength. The minimum factor of safety required for pins B, C, and D is 2.8 with respect to the pin ultimate shear strength. Determine the allowable load P that may be applied to the rigid bar at A. Use overall dimensions of a = 57 in. and b = 117 in. a b B kips P Answer: Pallow= i
Assuming k = 3000 lb/in2, and considering only the bending stress:What rail type would you recommend if two identical forces of P = 30,000 lb, 70" apart, are applied to it?
Please include FBD in your solution
Given W 16x36 section as shown below (Fy = 50 ksi, Fu = 65ksi). The holes are 3/4 inch in diameter. The connection is bottled at the web only. Assume x= 0.76 inch. 2. The shear lag coefficient U and the effective area Ae
Problem 2: Book Problem 3-9 (Hint: Only one of the two chains is at max tension, the other will be less.) 3-9. Determine the maximum force F that can be supported in the position shown if each chain can support a maximum tension of 600 lb before it fails. 30° SERDISC A Prob. 3-9 C
Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross sectional area of 1.35 in.² and a yield strength of 45 ksi. The pins at B, C, and D each have a diameter of 0.7 in. and an ultimate shear strength of 78 ksi. Each pin connection is a double-shear connection. Specifications call for a minimum factor of safety in member (1) of 1.5 with respect to its yield strength. The minimum factor of safety required for pins B, C, and D is 2.9 with respect to the pin ultimate shear strength. Determine the allowable load P that may be applied to the rigid bar at A. Use overall dimensions of a = 46 in. and b = 94 in. D (1) b A kips P Answer: Pallow= i a B
Current Attempt in Progress The five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in the bolts must be limited to 37 ksi, determine the minimum bolt diameter that may be used for this connection. %3D Answer: dmin in. %3D
Please show complete details, FBD, and solutions. Thank you!
Note: hand written solution should be avoided.
Design a clamp coupling to transmit 25 kW at 120 r.p.m. The allowable shear stress for the shaft and key is 50 MPa and the number of bolts connecting the two halves are six. The permissible tensile stress for the bolts is 75 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3.