2. For this circuit:findv,(t)(B)V₂(s)(a)for any R, L, C.V₁(s)(b) v₂ (t) if R = 1, L = 1, C = 1, andi. v₁ (t) = 8(t), orii. v₁ (t) = 5.CHF≤R _v₂(1)This means that you have two different input voltage signals. Each signal will give a differ-ent output v₂ (t) or V₂(s).

Given:a circuit, to find:a) Transfer function for any R, L, C.b) output voltage if R=1, L=1, C=1:

2. For this circuit: find (a) for any R, L, C. v₁ (1) V₂ (s) V₁(s) (b) v₂(t) if R = 1, L = 1, C = 1, and i. v₁ (t) = 8(t), or ii. v₁ (t) = 5. (A) B L 000 C= + R v₂(t) This means that you have two different input voltage signals. Each signal will give a differ- ent output v₂ (t) or V₂(s).

2. For this circuit: find (a) for any R, L, C. v₁ (1) V₂ (s) V₁(s) (b) v₂(t) if R = 1, L = 1, C = 1, and i. v₁ (t) = 8(t), or ii. v₁ (t) = 5. (A) B L 000 C= + R v₂(t) This means that you have two different input voltage signals. Each signal will give a differ- ent output v₂ (t) or V₂(s).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Problem 4: There is no energy stored in the circuit shown in Figure below at the time the switch is opened. a) Derive the integrodifferential equation that governs the behavior of the voltage vo b) Show that Vo(s) = lac/C s² + (1/RC)s + (1/LC) c) Show that Io(s): = slac s² + (1/RC)s + (1/LC) lac Voi
For the circuit given, if A = 450 mF obtain an expression for vd) valid for all t> 0. 20 k2 6 V t = 0 iR ic vc_0.1 Q. The expression for vd) valid for all t> 0 is A1e $1 + A2e $2²V, where A1 = x10-5, s S1 = A2 = x10-7, and S2 = ell
Consider the following circuit. In the circuit, A=3, R1= 3, R2= 62,and a=8 R2 A-Au(t) telt) R1 aic(t) 2F a) Determine the capacitor voltage at t-0 K -. Determine K s+p and p b) The expression for V(s) is c) Determine the value of v (t) at t=2 s d) What is the value of the time constant of the circuit for t>0?
ASAP
At t=0, the switch in the circuit below closes. Determine the voltage across the capacitor at the instant after the switch closes, Vc(0+) given R₁ = 82, R₂ = 90, R3 = 20, V₁ = 10V, and V₂ = 17V + t=o R₁ 20 C R₂
Find VouT(t) for t > 0 when the switch closes in the circuit below at time t = 0. The capacitor has no initial energy stored prior to t = 0. VIN = 5 V. Solve also for Vout(2t). 2F 200 200 t=0 VIN VOUT
We wish to find v(1) for 1>0 in the RLC circuit shown below where the elements are in series. a. Derive the governing equation for the voltage v using KCL at the top node using the following definitions: a = w = == You should obtain (see attached for a similar 2RC derivation from the book) d²v 1 dv + dt2 RC dt LC This will get you a governing equation in the same form as that derived for the case we did in class where the R, L, and C were in series. e. Plot v(t) until the transient dies out. Circuit v = 0 b. What is the particular solution in this case, i.e., what is the value of v after a very long time after the voltage and current have reached steady state? of c. If R=15.8 Q2, is the system underdamped, critically damped, or overdamped? What is the equation that describes v(t)? resistances or d. Determine the final equation for v using the initial conditions v(0)=5V and i(0)=0. (Hint: use KCL and i(0)=0 to find at t=0). dt and 1H sources LC (a) d²v dt2 1 mF dv + 2α t dt V ELE +w/v =…
Q1) For the circuit shown in Figure 1 below, find v(t)and i(t) for t> 0. Given R=492, C = 0.25 F and L = 1 H R t = 0 24 V + 1H m 0.25 F V Figure 1 + > 1 192
In the given circuit, where R = 1 ohm and and L=1H, solve for i(t) using convolution. The time-domain current source is(t) is given in the plot below. Hint: you can show your work graphically or state and solve a set of integrals to demonstrate convolution.
Exercise 3: Plotting two signals together (Matlab function: hold) Plot the following sinusoidal and exponential signals together between 0 to 8ms with step size le-5. x(t)=, a=(S1+S2)/1e4 fo2 = (270+K2) Hz, K2=(S1+S2)/1e6 02 Hint: Some helpful commands Definition of x (t) %% X=exp (-a*T) ; Definition of y(t) %% Y=cos (2*pi*fo.*T-pi/4) ; plot (T, X, 'k', 'linewidth', 2); hold; plot (T, Y, 'r-. ', 'linewidth', 2); hold; 1 0.8 0.6 0.4 0.2 受。 -0.2 -0.4 -0.6 -0.8 -1 0 x(t)=exp(-at),y(t)=cos(wt-pi/4), a=722.22 fo=277.22 1 2 3 4 Time (seconds) 5 6 7 8 X10-3
What is Vo(s) in the given circuit? It is given that the initial energy in the circuit is zero, and the ideal voltage source is 600u(t) V.
The switch closes at time t = 0 and we measure v(t) = 24 – 12e½us v for t>0 Find the values of R1, R2, and L1. R2 R1 + V R3 v(t) L1 Given Variables: Vs: 36 V R3:2 kohm