2. Draw the shear and moment diagrams for the beams shown without writing the shear and moment equation. Show all values at change in loading position and at points of zero shear. The value of P is the last two digits of your ID number (if it is 00 then use 10) with a unit of kN. 8 kN/m 9 kN/m B C 4 m 2m. 4 m 1/1 :::

Q: 10. The first digital code was the: a. ASCII code b. Baudot code c. Morse code d. none of the above

A:

Q: 35 aw the projections of this shape 25 20 20 A

A: GIVEN:   TO FIND: Draw the projection of the given shape.

Q: ( Centroid: Centroid is an imaginary point in a section where entire area of section is assumed to…

A: Brief concept introduction- The centroid is the average position of an object's points. When the…

Q: The following is the bearing and length measurements of an opentraverse A) Determine the latitude…

A: The latitude of the traverse line is extend on the north and south direction and departure of the…

Q: What do you mean by the Bulk Richardson Number (BRN)?

A: The Bulk Richardson Number is defined as the ratio of turbulence due to kinetic energy to the shear.

Q: To draw the figure below, the most :important command is Array O Trim O Сopy O Offset

A: Given data Grid of shape To be discussed Which command to be used

Q: In the exhibit below, What is the distance from A to C, A O 1078.57' O 1087.75' O 1187.57' O…

A: Given values: Consider closed traverse given. For closed traverse, sum of latitude and sum of…

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral.…

A:

Q: Find the centroid of the following cross-sections and planes.

A: Centrodal distanceX = 5.333 inY = 5.667 inExplanation:Step 1:Step 2:

Q: (x+yc )dx - (xc ) dy こ0

A:

Q: ARSWer ls With reference to the units systems, One full circle equals 400 Grades 180 15 30 2 TT

A: One Full Circle equals to 400 GRADES  And also 2π radians and 360°

Q: From the rectangular area shown a semi-circle of radius 4 cm is removed. Locate the centroid, (C),…

A:

Q: Determine the coordinates of the centroid 120 mm 240 mm uu ost

A: In a body, the centroid is the point where all its sides have the same volume. Those made from one…

Q: Determine the coordinates of the centroid of the shaded area. y | 25 E 50 60 25 60 70 50. --x 170…

A:

Q: Calculate the dimension marked in red X in the following figure

A: for the given structure shown  22×26  unit2 - dimensions of the upper block40 unit - length of the…

Q: R10 30 50 O. 15 R30

A:

Q: ") FOR THE GIVEN SECTION. (DImensions ore in mm ) a) Determnine the location of neutral as from the…

A:

Q: Determine the y-coordinate of the centroid of the shaded area. The triangle is equilateral.

A:

Q: Find the centroidal distances from x axis and y axis

A: Consider the figure,

Q: Arc command and its abbreviation is A character is the only command can be used to draw an arc in…

A: It is required to state whether true or false statement.

Q: Locate the X–X and Y–Y centroidal axes for the area shown.

A: The given figure is shown below:

Q: Z 10 mm 15 15 430 y y -y y 15 100 All dimension in mm FIGURE Q3 (a) FIGURE Q3 (b) IN

A: The dimensions of channel section are given.two channel sections are arranged back to back with 10mm…

Q: What of the following about the scale is/are false ?

A: The scale represents the ratio between the measurement drawn in a plan to the actual measurements.

Q: Locate the X–X and Y–Y centroidal axes for the area shown.

A:

Q: -20 +0.50 20/3

A:

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral. 16 35 +…

A:

Q: 9. Using cantilever method, determine the maximum absolute axial force in the column in kN due to…

A: Given data in question  Lateral loading Dimensions  Cantiler method  To find out  Axial forces in…

Q: Complete the partial multiviews provided belew, by filing in the miosing lines. NOTE: Missing lines…

A: given,

Q: St BS 0+00 3.54 0+10/ 0+20 1 1 1 1 I 2.994 2.044 0.171 00249 1.497 IS 3.269 2.966 Fs 1.845 1.840…

A:

Q: In the exhibit below, What is the distance from A to C, A O 1078.57¹ O 1087.75' O 1187.57' O…

A: To Determine Distance from A to C, L = ?

Q: Note: Replace all zero digits of your ID number by number "2" blem #5: Use X = Last 3 digits of ID…

A: To find tension in all cables

Q: 112 тm К30 тm ->- 30 тm -+30 тm ->-30 mт -> Рart a) Determine the moment of inertia of the shaded…

A:

Q: 11. Which IS codes gives details about elevators? A. O IS 27752 B. O IS 38665 C. O IS 14665 D. O IS…

A: IS code that gives details about elevators

Q: sanitary engineering  solve by hardy Cross method  k=8*f*L/pi*g*D^5 f=0.02 g=9.81 pi=e.14

A: Given data in question  Length of pipe  Diameter of pipe Constant value of f Acceleration due to…

Q: *9-64. Locate the centroid (, y) of the shaded area. y 1 in. 3 in 3 in. 3 in. Prob. 9-64 Ai=…

A:

Q: Identify the centroid of the 1/4 circle projected whose radius is r. Utilize integration. Yo -x Хо

A:

Q: Locate the centroid of the given area below. Semi-Circle Square

A:

Q: 11. Which IS codes gives details about elevators?

A: IS stands for Indian Standard

Q: Determine the coordinates of the centroid of the shaded area. 10 40 y X = K15 Answers: y= i 10 |10|…

A:

Q: Determine the location of centroid from x and y-axis.

A: To find centroid

Q: Determine the coordinates of the centroid 120 mm 240 mm 150 mm

A:

Highway Surveys and Location

Surveying is an operation in the civil engineering domain that requires collecting and identifying data regarding an area of land and topography. The data that is collected can be helped to plan and undertake the construction process. Civil engineers perform surveys to gather three-dimensional information regarding a particular area. Engineers specify several points on the surface of the earth and relationship between points, and the distance and angles between the points are evaluated. The data from this evaluation guides in drawing plans regarding buildings and structures.