2. Compute the resultant of the three forces acting on the plate shown in the figure. Locate its intersection with AB and BC

Q: Q1/ A. Write the force system for each one of the following? JIL

A: Given:-  To Find:-  Type of force system

Q: 12-x2 了了少 Je

A:

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each…

A: Consider a vehicle engine where number of cylinder are situated whose bore diameter is D and stroke…

Q: Q/ The force in the member (CA) is 12m 50 ку. 10 points 5m 16x

A:

Q: Write the four different types of Resultant Loadings?

A: Loading: The loading on the beam or any members is the load acting on a beam under which beam…

Q: Forces and moments are scalar Forces are moments are vector quantities.

A: Forces and moments are both physical quantities that can be used to describe the behavior of objects…

Q: The coefficient of bend value in the energy loss due to bend in a pipe depends on the pipe diameter,…

A: Coefficient of bend value depends on ?

Q: 360 degrees of crankshaft rotation. 1. A revolution is 720 2. The camshaft rotates degrees during…

A: To find :-  Fill in the blanks

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: Relative angles provide more information about segment position than absolute angles Select one:…

A: Given Data : Relative angles Absolute angles

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is…

A: Solution for Question 24: Given, Mass of arm = m = 100 kgWeight of arm = W = mg = (100) (9.81) = 981…

Q: Q 4/ Give the names of the components to the parts in the vehicles According to the figures. Cutch 4…

A: Data given-

Q: 1500# 1500# 1500# 1500# 12' K I

A: In this problem, following steps will be taken 1. Determine the reactions at the supports.' 2. Using…

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: In the moment calculation, why did you take away the h* from 8?

A:

Q: 3. Tubing used for air-conditioning installations is usually insulated at (a) the low-pressure side…

A: Tubing used for air conditioning installations is usually insulated at the low-pressure because the…

Q: 35 - Which of the following statements about supports is false? A) There is no freedom of movement…

A: Degrees of freedom is the no of the independent variable required to define the movement of a…

Q: Exalo S. F.d 4o KN/m Braw and B.M.d Ax=o,た Sohato Ay

A:

Q: 250cm+10m

A: Given Data : 250cm+10m

Q: Which of the following statements below are incorrect? select all which apply.     A shear force…

A: It is needed to provide the wrong or incorrect statements.

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: Indicate whether the terms are like or unlike. - 322, 5z? ... The two terms 5z and - 3z are

A: The two terms 5z2 and -3z2 are like terms.

Q: Which of the following statements is CORRECT? Don't Know A force can be moved along its line of…

A: Given problem is

Q: Complete the each drawing by adding the missing details in 5 and 6 both questions.

A:

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”

Q: Which of the following statements is/are true? 1. The force per unit area, or intensity of the…

A: Stress is defined as the ratio of force applied to the body to the cross sectional area of the…

Q: in speed during bending why are you multiplying the speed during bending by 5/18

A: To answer: Why speed is being multiplied by 5/18.

Q: Where did you get the 3 from for the distance of q?

A:

Q: Calculate each moment by multiplying each force with its distance to the reference point, and add…

A:

Q: 2. The size of 1/2 in. would refer to the with regard to ACR copper tubing.

A: The correct option is (b)  Outer Diameter (OD)

Q: Find the vertical force component for the figure 800 N y 50°

A: Given data :-  Force F = 800 N  Theta = 50°  Find :-  Vertical component = ?

Q: a) Calculate the thigh, shank and knee angles based on the XY coordinates of the hip, knee and ankle…

A: Given DataCordinatesKnee=1.2,0.5Ankle=0.9,0.1Hip=1.1,0.9