2. (CASTIGLIANO'S THEOREM) Determine the vertical displacement of point B of the beam shown below. E= 200 GPa I= 150(10) mms P= 15.4 kN Q= 6.4 kN/m a = 6 m

Q: с kN b kN/m A -B |C "a" m "a" m

A:

Q: Determine the horizontal displacement at C (Acx) by used Castigliano method Dont calculate the EI…

A:

Q: Determine the vertical displacement at B (ABY) by used Castigliano method Dont calculate the EI Ang…

A:

Q: Situation 7:The steel bar BC is supported by the steel rod AC of cross-sectional area of 170 mm², E…

A:

Q: From the figure shown, find the horizontal displacement at B in kNm³/El. El is constant. 20 kN B…

A:

Q: Given the figure below, determine the deflection at B if El is constant 40 kN/m 40 kN/m B A 3 m 3 m

A:

Q: Consider the structure below. Using virtual work, compute the vertical displacement at point C. 30…

A: Given: A frame with loading on it  E = 200 GPa, I = 300*10⁶mm⁴ Required: Vertical displacement at C…

Q: By using Conjugate Beam Method, find the rotation at C (0c) and the deflection B (8B) for the beam…

A: Consider the moment about point B in the beam.

Q: Determine

A:

Q: Determine the reactions at support and the forces acting on each member. By applying 1 unito load…

A:

Q: Use the stiffness method to determine the horizontal and vertical components of the displacement at…

A: Modulus of elasticity , E=206.8 GPaArea of members , =1290 mm2 Also , i=80KN and j=150 KN

Q: 6. Solve the below structure with displacement method, and plot out its M diagram. EI= constant.…

A:

Q: 60⁰ Find the vertical and horizontal displacement at point C using the CASTIGLIANO THEROEM (de) v =…

A: Given data:

Q: Determine the slope at B and the maximum displacement of the beam shown in the figure below (Figure…

A: Given, Beam loading diagram   To find : Slope at B and maximum displacement

Q: E F G 1[KN] A D Figura 2 B 2.

A:

Q: 1. Use slope-deflection method to solve the moments listed in ansSheet. And compute the displacement…

A: In slope deflection method ,first we need to find out the fixed end moment corresponding to each…

Q: A simply supported beam is shown in the figure. El = 56,000 kN-m2. Using Double Integration Method…

A:

Q: Show full and clear solutions. Use the SLOPE-DEFLECTION METHOD to answer the following question(s).…

A:

Q: For the following beam use the method of virtual work to determine: (a) Solve for the slope at B…

A: “Since you have asked for multiple methods, we will provide the solution only using the first method…

Q: Calculate the horizontal and vertical displacement of point B. Rod cross-sectional areas A = 1050…

A:

Q: By Double Integration, find the magnitude of the midspan deflection. Assume El is constant. 6W…

A: Given  W= 84

Q: Analyze the beam 4P (kN) 2P (kN/m) 80° 3m 3m 4m 3m

A:

Q: Find the sehimi at the BC midpoint of the loaded beam as shown in the figure by the double-laye…

A:

Q: #2. Determine the horizontal displacement at point A. E = 200,000 MPa, a cross-sectional area = 600…

A: Step 1:Step 2:Step 3:  Hope this helps!

Q: Problem 1. Determine the displacement and slope at C. EI is constant. Use the conjugate beam method.…

A: Given values: A simply supported beam with overhang and 2 point loads. EI is constant. Using…

Q: The beam below, use the double integration method to determine the deflection at point A (do not use…

A: To determine the deflection at point A using the double integration method.   Applying the Double…

Q: Determine the value of a in meters so that the deflection at point C is equal to the max deflection…

A:

Q: 20. A 6-meter simply-supported beam is loade with a 2kN/m uniform load and a 10kN concentrated load…

A:

Q: Find the slope at the deflection. Take L = 8 mothod

A:

Q: : Determine the amount of deflection at free also the maximum deflection. Use W = 35 kN/m, M = 15…

A:

Q: Determine the the vertical component of the displacement at point"d" for the shown beam. 2m b 7 50…

A: A double overhanging beam is loaded with uniformly distributed load, we need to find the vertical…

Q: angular position of the slotted bar is e = 10t^2 rad. Determine the (measured magnitude and…

A: Sine law: - It is defined as an equation by which one can relate the length of side of triangle to…

Q: 2. Determine the internal moments of the beam shown, Support A settles 10mm. E=200 GPa, and I =…

A:

Q: a kN 3 m 4 m 3 m B b kN

A:

Q: Compute the deflection at C using conjugate beam method,

A: Given, The beam is A 'Cantilver Beam' Span of the beam = 6m There is 3 point loads having magnitude…

Q: Use Virtual Work Method to answer the questions below considering the truss shown in the figure.…

A:

Q: Determine the displacement at B. 12 m I 80 kN B E= constant = 200 GPa I=600 (106) mm* 12 m 21 C

A: E=200 kN/mm2 I=600 * 106 mm4 To find displacement at point B

Q: A statically determinate beam with two pin supports at A and B is shown in Figure 1. Use virtual…

A: Given:Required:Deflection at C using virtual work method

Q: 30 kN 20 kN 20 kN/m 15 kN/m 2.5 m 7 m 3 m 8 m

A:

Q: Using double-integration method, determine the slope and the displacement at the end of the C of the…

A:

Q: Problem Set 2: The simply supported steel beam is loaded by the 20 kN - m couple as shown in the…

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.