Use the stiffness method to determine the horizontal and vertical components of the displacement at Joints C and D. For all bars, E = 206.8 GPa and A = 1290 mm². Take i = 80 kN and j = 150 kN. D A 4.88 m 0 с B 000 3.66 m Joint C: a) Δ. b) Ay= = Joint D: c) AT d) Ay = || mm mm mm mm

Use the stiffness method to determine the horizontal and vertical components of the displacement at Joints C and D. For all bars, E = 206.8 GPa and A = 1290 mm². Take i = 80 kN and j = 150 kN. D A 4.88 m 0 с B 000 3.66 m Joint C: a) Δ. b) Ay= = Joint D: c) AT d) Ay = || mm mm mm mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 454 For Problems 20.17 through 20.20, use the matrix approach to solve fo the member end forces. In…

Q: Using the method of virtual work, determine the vertical displacement of joint A of the truss shown…

Q: The two bars (A = 2 in.? and E = 30 ksi) shown in figure shown are used to support a load P = 20 lb.…

A: Determine the horizontal displacement of point B.

Q: 10.Determine the vertical displacement of joint C of the truss. Each member has a cross-sectional…

A: Given data: A=300 mm2. E=200 GPa.

Q: 1. From figure 1.1. Determine the distance 'a' as a fraction of the beam's length 'L' for locating…

A: Take moment about A∑ MA=0 3PL-RCL-a+PL6=0RC=196PLL-a∑ Fy=0 RA+RC=4PRA=4P-196PLL-a

Q: Determine the slope and displacement of point B of the steel beam s

A: Modulus of elasticity (E)= 200 GPaMoment of inertia (I)= 60*106 mm4A Beam system given in the figure…

Q: A tapered bar AB of solid rectangular cross-section with a thickness of 20 mm and length L = 800 mm…

A: In this question a paper bar is given Thickness 20 mm Length is 800 mm Force is 25 KN Width of bar…

Q: Consider the truss shown in (Figure 1). Assume the members are pin connected at their end points.…

A: E = 200 GPa = 200 × 103 N/mm2 A = 200 mm2 Determine the vertical displacement of joint C using…

Q: sing a method of your choice, calculate the displacement at end D due to the distributed load.…

A: As there are 2 supports B and A and D taht are free ends. At B and C, slope θ but the displacement…

Q: Q. I For the truss shown in Q. $. determine the horizontal and vertical components of the…

A: Given:- The truss is given with two forces acting on it The magnitude of the vertical force at B =…

Q: The cross sectional area of each member of the truss shown in the figure is A = 500 mm^2 and E = 200…

Q: Determine the vertical displacement of joint A. Each bar is made of steel and has a cross-section…

A: Given: The cross-sectional area is 600 mm2. The modulus of elasticity is 200 GPa. Consider the…

Q: Determine the bar force of member BD (in kN) of the truss shown if P 18 kN and Q = 90 kN. Use 3…

Q: The loading of the truss is represented below. EA = 50 x 106 N Question 1. Determine the…

A: Given Data AE = 50 × 106 N Determine 1. Vertical displacement of joint-B. 2. Joint-C overall…

Q: Determine the vertical displacement of joint A (a) if members AB and BC experience a temperature…

Q: Using the virtual work method, determine the vertical displacement of joint Cof the steel truss…

Q: Problem 4 ust. The beam shown below is subjected to the load shown in the figure. Use the…

Q: Consider the truss shown in (Figure 1). AE is constant. Assume that AE is in kN. Use the principle…

A: Using principle of virtual work, we need to find out horizontal displacement of joint C

Q: Q#5. Determine the displacement at point C and slope at point B of the steel beam shown. El is…

Q: a 33.8 kN, b 27.2 kN, c-4.8m KN D "KN KN 4m 5m A-40 x 10 mm² A - 60 x 10 mm² C B H K J A-40 x 10³…

Q: Use the Unit Load Method to co the horizontal displacement AAX of joint A following planar frame.…

Q: The cross sectional area of the members of the truss shown is 500 mm² and E = 200 GPa. Solve the…

A: To find out the horizontal displacement of joint C due to external loading in mm.

Q: A statically indeterminate truss is shown in Figure 4b. Support at A is a pin and E is a roller. The…

A: Use virtual work method to determine the vertical displacement at C.

Q: Determine the horizontal displacement of joint A. Each bar is made of A992 steel and has a…

A: The given data is: Length of bar AB = 6 ft AD = 5 ft BD = 5 ft DC = 3 ft Cross sectional Area of…

Q: Determine the horizontal displacement of point C on the frame shown in Figure 4. Take and for both…

A: E = 29 × 103 ksi I = 400 in4 Determine the horizontal displacement of point C on the frame.

Q: Using Conjugate-Beam Method, determine the displacement at B. 12 m I 80 KN B E = constant = 200 GPa…

Q: Determine the vertical displacement of Joint A using virtual work method. Support C is a roller and…

A: Concept Here we will use method of virtual work,in which we first calculate the real forces using…

Q: Determine the vertical displacement of joint A if members AB and BC experience a temperature…

Q: -kN, b- 39.2 kN, c = 2.7 m a" kN D H "c" m b" kN C K "c" m b" kN B J "c" m 4 m 5 m A = 40 x 10º mm?…

Q: Use the method of virtual work and determine the vertical and horizontal displacement of joint F of…

A: For the given truss, the vertical and horizontal deflection at joint F have to be determined. Given:…

Q: Determine the horizontal displacement of joint C using Castigliano's theorem. Each steel member has…

Q: Using the conjugate-beam method, determine the displacement at D and the slope at D. Assume A is…

Q: Question 3 The rigid bar AB, attached to aluminum and steel rods, is horizontal before the load P is…

Q: 70 kN "a" kN 50 kN "a" kN "c" m A B C D. 4 at "b" m

A: Here we use a) Method of joints to find the member forces. b) Virtual work method to find the…

Q: Problem 1. Determine the vertical displacement of joint A. Each bar is made of steel and has the…

A: Note: As per Bartleby guidelines, only first question will be discussed. Given truss diagram is…

Q: Consider the truss shown in (Figure 1). Assume the members are pin connected at their end points.…

A: Given data : A = 130 mm2 E = 200 GPa Concept : Method of virtual work done - It is also known as…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

Use the stiffness method to determine the horizontal and vertical components of the displacement at Joints
C and D. For all bars, E = 206.8 GPa and A = 1290 mm². Take i = 80 kN and j = 150 kN.
i
D
A
4.88 m
с
B
3.66 m
Joint C:
a) Ar
b) Ay
Joint D:
c) Δ.
d) Ay
||
mm
mm
mm
mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Member stiffness matrix

VIEW

Step 3: Joint force matrix

VIEW

Step 4: Displacement

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 29 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

10.Determine the vertical displacement of joint C of the truss. Each member has a cross-sectional area of A = 300 mm² and E = 200 GPa. Use the method of virtual work. H 3 m B E 4 m D - 4 m 4 m 4 m 3 kN 3 kN 4 kN Figure Q10
The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.27 in2. Find the vertical displacement (in inches and absolute value) of point C caused by the 2448-lb load if x = 9.5 ft and θ = 41.7ᵒ. Use E = 29147 ksi for steel. Note: Round off the final answer to four decimal places.
Find the support reactions at joints A and D, then solve for internal forces at the top of member BC. Use numerical properties given. Use attached Table 1-1 for your reference. 90 D C 91 E b d 4 В a FB MA A a = 4 m b = 2m C = 3.5m d = 3 m MA = 380 N.m FB = 250 N 9o = 100 N/m 91 = 150 N/m %3D 3.
Q#5. Determine the displacement at point C and slope at point B of the steel beam shown. El is constant CLO2PLO2 C
Using the virtual work method, detemine the vertical displacement of joint Cof the steel truss shown in Figure Q3. Assume E= 200 GPa and A = 500 mm for all members. 4 m 300 kN Im 120 kN 4m 4m Figure Q3
helpppp
The cross-sectional area of each member is indicated in the figure. Assume the members are pin connected at their end points. Use E = 29 * 10 ^ 3 * ksi A. Determine the vertical displacement at joint A. Using virtual work method B. Determine the vertical displacement at joint C. Using Castigliano's Theorem
Use the VIRTUAL WORK method. a.) determine the vertical displacement of joint A. Each bar is made of steel and has a cross-sectional area of 600 mm^2. Take E= 200 GPa. b.) why solving the reactions of the supports is not needed or necessary?
Using Method of Area solve.. The beam has a loose fit built-in support at B which allows the end of the beam to rotate through the angle Ө0 = 0.75° when the load is applied, as shown in the detail. E = 72 GPa and I = 120 x 106mm4. Determine the following: Reaction at A (kN) Moment at B (kN m) Slope at A in radians Displacement at the application of 200kN load
1. A Using E = 100 GPA. IN.A. = 1,500 x 10 mm², compute the SUPPORT REACTIONS of the loaded beam shown when: a. supports are unyielding. b. support at the midspan yields 4 mm. 4m 60 KN/m B 2m www 10 KN C D 2m
Determine the displacement at B using Conjugate-Beam Method
P=67