2. An artillery piece and integral supporting base weigh 1800 lb and have a recoil spring for which k = 24000 lb/ft. When fired, the system recoils 40 in. A dashpot having a critical damping constant is the engaged on the return stroke. Determine: (a) The initial velocity of recoil (b) The damping constant (c) The position of the gun and base at 0.5 sec of the return stroke.

2. An artillery piece and integral supporting base weigh 1800 lb and have a recoil spring for which k = 24000 lb/ft. When fired, the system recoils 40 in. A dashpot having a critical damping constant is the engaged on the return stroke. Determine: (a) The initial velocity of recoil (b) The damping constant (c) The position of the gun and base at 0.5 sec of the return stroke.

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter10: Introduction To Simulation Modeling

Section: Chapter Questions

Problem 41P: At the beginning of each week, a machine is in one of four conditions: 1 = excellent; 2 = good; 3 =...

See similar textbooks

Similar questions

A LVDT type displacement transducer with a primary of 300 turns and secondary of 500 turns in each section is excited with a carrier wave signal of 1 kHz, 5 mA current. The width of the primary coil and each secondary coil is 10 mm, the thickness of the windings is 4 mm and the radius of the outer coil is 8mm. Calculate the sensitivity of the device and the percentage output linearity at 10% and 20% of the primary coil width.
The 180-mm disk is at rest when it is placed in contact with a belt moving at a constant speed. Neglecting the weight of the link AB and knowing that the coefficient of kinetic friction between the disk and the belt is 0.44, determine the angular acceleration of the disk while slipping occurs. 180 mm K 60° B The angular acceleration of the disk is 63.1019 ✪ rad/s² 0.
A cosmetics company fills its best selling jars of facial cream by an automatic dispensing machine. The machine is set to dispense a mean of 7.2 ounces per jar. Uncontrollable factors in the process can cause either underfill or overfill, both of which are undesireable. In such a case, the dispensing can be stopped and recalibrated. Regardless of the mean amount despensed, the standard deviation of the amount dispwnsed always has a value of 0.25 ounce. A quality control engineer routinely selects 36 jars from the assembly line to check the amounts filled. On one occasion, the sample mean is 7.8 ounces. Determine if there is sufficient evidence in the sample to indicate, at the 1% level of significance, that the machine should be recalibrated.
do fast
do fast
1m radius disk is moving on the inclined surface under no slip condition. the center of the disk has 3m/s velocity and according to the figure, bar BC is pinned to the disk at point C and point B always stays on the ground. 1) find angular velocity of BC. 2) find angular acceleration of BC
a) A centrifugal pump has an impeller with dimensions r₁ = 75 mm, r2 = 150 mm, b₁ = 50mm, b2 = 30 mm, ẞ1 = ẞ2 = 30°. For a discharge of 70 L/s and shockless entry to vanes. compute (a) the speed, (b) the head, (c) the torque, and (d) the power. Neglect losses (α1 = 90°).
Tolerance is the allowable amount of error above and below an ideal measurement. In a manufacturing firm, a detergent carton claims to contain 1.5 kg. The manufacturer allows for a tolerance of +0.005 kg per box of 24 cartons. Find the maximum and minimumacceptable amounts of detergent per box.
do fast
Which of the following statements are best suited for the property "ductility" a. It is the ability of material to resist the deformation under tensile load b. It is the ability of material to resist the deformation under compression load c. It is the ability of the solid material to stretch under tensile strain d. It is the property of material to get fracture when subjected to the stress but has a little tendency to deform before rupture don't use chagpt only explain step by step.
Consider a product that is "settled in." Its MTBF distribution has been found to be normal with a mean of 10,000 hours and a standard deviation of 100 hours. Answer the following questions: (a) Calculate the probability of a breakdown before 8,000 hours? (b) Calculate the probability of a breakdown before 9,000 hours? (c) Would you prefer a policy of “preventive maintenance” or a policy of “breakdown maintenance” on this product? Explain your choice.
Meena Chavan Corp.’s computer chip production process yields DRAM chips with an average life of 1,800hours and s = 100 hours. The tolerance upper and lowerspecification limits are 2,400 hours and 1,600 hours, respectively. Is this process capable of producing DRAM chips tospecification?