2. A vertical Venturi meter is being used to measure the flow of oil of relative density 0.88 in a 200 mm diameter pipe. The throat diameter of the venturi is 100 mm and the discharge coefficient is 0.96. Two tapping point at the throat and entrance are 320 mm apart and the pressure difference between these is measure at 28 KN/m². a) What is the discharged in the pipe in m³/s. b) If a mercury manometer were attached at the tapping points, what would be difference in levels of the two arms of the manometer in meters. Show correct figure

2. A vertical Venturi meter is being used to measure the flow of oil of relative density 0.88 in a 200 mm diameter pipe. The throat diameter of the venturi is 100 mm and the discharge coefficient is 0.96. Two tapping point at the throat and entrance are 320 mm apart and the pressure difference between these is measure at 28 KN/m². a) What is the discharged in the pipe in m³/s. b) If a mercury manometer were attached at the tapping points, what would be difference in levels of the two arms of the manometer in meters. Show correct figure

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What is the quantity (short ton) of C1 (Designation: W24x104, Dimension: 24x12x0.8x0.5) ? Note Answer by a number with two decimal places Disregard the web thickness
Q19. Q20. Q21. Which are the followings technologies inclusive in Industrial Revolution 4.0 A. Pre-fabrication and Modular Construction B. Advanced Building Materials C. Building Information Modelling D. All of the above is correct Which of the following is best describe BIM timeline Level 2 A. Full integration. Full collaboration and full integration in a cloud-based environment. Include Asset Life Cycle and Facilities Management(7D) Low Collaboration. Computer Aided Design (CAD) is used to create drawings. Paper and prints are shared with the team. Full Collaboration. Adds additional dimensions such as Time Management and Budget Calculation. Full collaboration and partial interoperability through the use of distinct CAD model. D. Partial Collaboration 2D drafts are combined with 3D models in a Common Data Environment (CDE). Limited collaboration. B. C. Which of the followings statement describes about the Life Span of product in decision making for a project? I. II. IV. A. B. C. D.…
A roofer is working to cover a 2,720 SF roof. He has to first install rafters, sheathing, felt, and finally shingles. He assumes the previous tasks make up 35%, 20%, 15%, and 30% of the total roofing activity. At a certain point, he got the following information on the subtasks: Subtask Unit Rafters EA Sheathing SF SQ SQ Felt Rafters Sheathing Shingles 1 SQ = 100 SF Using the percent that each sub-task makes up of the total roofing task and the percent complete of each task based on quantity installed, calculate the estimated percent complete for the roofing activity. You need to enter the percent complete of each sub-task and the percent complete for the total ruffing activity. Felt Choose... Choose... Choose... Shingles Total ruffing activity Choose... ♦ Total quantity 150 2720 27.2 27.2 Choose... Installed quantity 102 1200 10
Please don't copy from other websites..
A beam is constructed from three boards bolted together as shown. Figure $= 250 mm 25 mm 25 mm 100 mm 350 mm V 25 mm < 1 of 1 250 mm Part A Determine the shear force developed in each bolt if the bolts are spaced s = 250 mm apart and the applied shear is V = 33 kN. (Figure 1) Express your answer with the appropriate units. F = Submit Value Request Answer < Return to Assignment Units Provide Feedback ?
Calculate the values of Xbar and Ybar to the centre of gravity of the shape shown below. Show all workings. 200mm Xbar 50mm Not to scale 80mm Figure 1b
1. What is a Free Body Diagram (FBD)? * Enter your answer 2. Provide illustration of a Free Body diagram.
(b) Compare type of product architectures with related examples for each type. Your answer
Which of the following is the best communication channel for complaining to the supplier? Select one: a. Calling to personal mobile phone of contact person b. Sending a short message C. Writing an official email
Method validation includes studies of precision and accuracy of a proposed method. How would you validate precision and accuracy?
The required total period for project completion and the critical path is determined after calculating the values in the empty boxes as in the symbol attached to the drawing
You have just completed 3 projects as detailed in the table below. Calibrate the SIMPLIFIED-COCOMO model provided in the unit materials and predict the duration of a project with 38,000 lines of code. Project Person Months LOC 1 1.8 16,000 2 1.3 12,000 3 1.7 16,000 Answer: