2. A singer voice is sampled for 4 second by an 8-bit ADC at a sampling frequency of 10 kHz. The samples are stored on a memory chip. i. What is the minimum memory size both in [bits and bytes] required to store all the samples? ii. How long the signal must be sampled to store the samples in 100Mbytes CD- ROM ii. What should be the highest frequency component of the signal?

2. A singer voice is sampled for 4 second by an 8-bit ADC at a sampling frequency of 10 kHz. The samples are stored on a memory chip. i. What is the minimum memory size both in [bits and bytes] required to store all the samples? ii. How long the signal must be sampled to store the samples in 100Mbytes CD- ROM ii. What should be the highest frequency component of the signal?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4- If the input signal is 100KHZ, can we make sampling for this signal when it applied to the analog input port of Arduino, explain?
This multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer. 11)The output signal-to-noise ratio of a uniform quantizer, for a full load test tone, is equal to 61.8 dB. The number of bits per sample is a)none of the mentioned b)9 c)8 d)10
An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 3.2kHz. If the system is operated at a bit rate of 36,000 bits per second (bps), answer the following: a) To avoid aliasing, the sampling frequency must be greater than or equal to kHz b) If the signal is sampled at the Nyquist rate, what is the Nyquist frequency? kHz h c) If the signal is sampled at the Nyquist rate, the number of bits per sample is number of quantization levels is and the Note: *When you use the formula bFs L in finding b, the result must be rounded up to the nearest integer.
What is meant by resolution? How is it related to the accuracy of ADC?
In sampling a 3.4 KHz telephone quality voice signal using 10 bits, the average number of steps taken by the ramp method of analog to digital conversion is:
10101010000 Binary frequency shift keying (FSK) is adopted as the modulation technique. The FSK modulator specification is as follows: Bit Rate: 20000 bit/sec Carrier Signal: 50 sin (2n 60000t) Frequency shift, Af= 20000 Hz i) Determine mark and space frequency for this system. ii) Sketch the output for the digital signal.
3/ An analog signal is converted to a binary PCM signal and transmitted over a band-limited channel at 100 kHz. band-limited channel at 100 kHz. Thirty-two quantization levels are used. a/ Calculate the maximum bit rate that can be transmitted. b/ Calculate what is the maximum bandwidth that the analog signal can have.
For a signal in the range of 6 to 63, in order to have a resolution of 0.17, we need. Number of levels Select one: a. 337 b. 338 c.333 For the device measuring temperature in the range of 36.8:44.5, and the results are stored in 5 bits, the step size is Select one: a. 0.24839 b. 0.03182 c. 2.62258
An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 3.2kHz. If the system is operated at a bit rate of 36,000 bits per second (bps), answer the following: a) To avoid aliasing, the sampling frequency must be greater than or equal to kHz b) If the signal is sampled at the Nyquist rate, what is the Nyquist frequency? kHz h c) If the signal is sampled at the Nyquist rate, the number of bits per sample is number of quantization levels is and the Note: *When you use the formula bFs L in finding b, the result must be rounded up to the nearest integer.
12 )Which is not the downside of analog signal processing? Difficulty keeping informationHigh sensitivity to electrical noiseLimited dynamic range in signal amplitudeRobustness against noiseRepeatability
An analog signal having a maximum frequency of 10 kHz is being transmitted through a PCM system with a uniform quantizer having 256 levels. What will be the minimum transmission bandwidth of the transmitted PCM signal?