An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 3.2kHz. If the system is operated at a bit rate of 36,000 bits per second (bps), answer the following: a) To avoid aliasing, the sampling frequency must be greater than or equal to kHz b) If the signal is sampled at the Nyquist rate, what is the Nyquist frequency? kHz h c) If the signal is sampled at the Nyquist rate, the number of bits per sample is number of quantization levels is and the Note: *When you use the formula bFs < Bit Rate in finding b, the result must be rounded down to the nearest integer. **When you use the formula 2 > L in finding b, the result must be rounded up to the nearest integer.

An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 3.2kHz. If the system is operated at a bit rate of 36,000 bits per second (bps), answer the following: a) To avoid aliasing, the sampling frequency must be greater than or equal to kHz b) If the signal is sampled at the Nyquist rate, what is the Nyquist frequency? kHz h c) If the signal is sampled at the Nyquist rate, the number of bits per sample is number of quantization levels is and the Note: *When you use the formula bFs < Bit Rate in finding b, the result must be rounded down to the nearest integer. **When you use the formula 2 > L in finding b, the result must be rounded up to the nearest integer.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1- A music signal has frequency content from 0 Hz up to 8.75 kHz. (a) What sampling frequency must be exceeded for successful A/D conversion? (b) What is another name for the minimum sampling frequency?
Solve in digital format please In your words, describe what the signal modulation process consists of.
We want to design a digital circuit that converts Gray code (ABC) to Binary code (xyz). Set up a 8-to- 1 line multiplexer so that the output gives y as a function of ABC. "A" is given to the most significant bit of the control inputs of the multiplexer. "C" is given to the least significant bit of the control inputs of the multiplexer.
Pulse-code modulation (PCM) is the standard form of digital audio in computers, compact discs, digital telephony and other digital audio applications. Figure 3 shows the 3bit PCM system that transmit the 250 kHz analog signal with the voltage range from -6 mV to 6 mV. i) Identify the quantized value, voltage range and binary code for each level by building your own quantization table. ii) Calculate the minimum sampling rate and sampling time. ii) Identify the corresponding sampled voltage, the quantized voltage and binary code if the input signal is sampled at time t1 = 2us, t2 = 4us, t3 = 6us, t4 = 8µs. iv) Sketch the output in (iii) if it is fed to Manchester coding line encoder with bit rate of 20000 bit/sec and amplitude of +4 V. 5 4 3 2 10 Timel(usec) Figure 3 Amplitude (mV)
The plot below shows a sampled continuous signal, with red dots indicating sample points. Determine if the signal has been sampled appropriately, so as to avoid aliasing. For the case where the signal has not been sampled appropriately determine the aliased frequency and enter the result in the answer field below (enter a numerical value only +- 5% tolerance). For the case where the signal has been sampled sufficiently enter the sampling frequency. Amplitude 30 20 10 0 -10 -20 -30 0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1 Time (seconds)
Choose the correct answer low HDOP (Horizontal Dilution of Precision) number such as2 indicates a ........................... a.poor fix b.good fix c.poor signal quality d. good signal quality
If there is a signal m(t) = 5sin2000πt + cos4000πt + 2.5cos3000πt will be changedinto a digital signal with the ADC device.a. Determine the minimum sampling frequency according to the Nyquist condition!b. What is the distance between samples in ms?
Depanment of Electronics Engineering IX. A carrier signal is amplitude modulated by a sinewave. The resulting AM waveform Is shown below. zed 6V 2.5V a) What is the percentage of modulation? b) What is the amplitude of the carrier signal? c) To achieve 75 percent modulation, what amplitude of the modulating signal is needed? d) Calculate the effective voltage of the AM signal SSA AILE Q + Page 4 I 5 X. The frequency spectrum of an AM signal is shown betow: (9 pts)
Related to communication system
The spectrum of a signal extends from 200 to 3200 Hz. The minimum sampling frequency required isa. 6 kHz b. 1.5 kHz c. 3 kHz d. 9 kHz
Construct MOD 12 asynchronous counter. What will be the output frequency, if the input frequency is 1 MHz. If the counter is at state 6, what will be the count after 60 pulses.
An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 900Hz. If the system is operated at a bit rate of 180kbps and each input sample is quantized into 1024 levels, answer the following: a) What must be the minimum sampling frequency to avoid aliasing? samples/sec b) What is the Nyquist rate? c) What must be the number of bits per sample? kHz Hz bits d) If the sampling frequency is 10% above the Nyquist rate, what is the Nyquist frequency?