2. A "scale" is constructed with a 4-ft-long cord and the 10-lb block D The cord is fixed to a pin at 4 and passes over two small pulleys at B and C. Determine the weight of the suspended block at B if the system is in equilibrium when s=1.5 ft. I ft Figure: 03_POB9

Q: Determine the reactions at support A of the rigid body shown in the image. Also, indicate on your…

A:

Q: Determine whether the block shown in the figure is in equilibrium and find the magnitude and…

A: Draw a free-body diagram of the block.From the diagram, it is clear that the block is in…

Q: A "scale" is constructed with a 4.1-ft-long cord and the 15-lb block D. The cord is fixed to a pin…

A:

Q: ha ding BAC is used to lift the 10-kN load with constant velocity. By drawing the free-body diagram…

A: As per the company's guidelines when multiple questions are asked only first question has to be…

Q: The unstretched length of spring AB is 1 m. If the block is held in the equilibrium position shown,…

A:

Q: THE SYSTEM SHOWN BELOW IS IN EQUILIBRIUM IF THE WEIGHT OF B IS 48 NEWTON CALCULATE THE WEIGHT OF A,…

A:

Q: Problem Statement Based on Problem 6-64 from the textbook. Determine the force P required to hold…

A: Given data  Mass = 51kg Find the force P

Q: Draw a complete free-body diagram for the system. Calculate the reactions at both supports needed…

A: i) Free body diagram where, RA= Vertical reaction force at A            RC= Vertical reaction force…

Q: 1. Plate ABCDEF is a sliding door supported by a frictionless linear bearing at A and a frictionless…

A: The total weight of gate is

Q: Problem Statement Based on Problem 6-11 from the textbook. The spring has an unstretched length of…

A: Given data x = 1.6 m  L = 0.35 m  k = 160 N/m  θ = 30o(at equilibrium)   To determine  mass of…

Q: Determine whether the block shown is in equilibrium, and find the magnitude and direction of the…

A: Given: The magnitude of force P is P= 120 lb. The static coefficient of friction is μs=0.40. The…

Q: Two forces F1 150 N and F2 50 N to hold the weight of 200 N. Check and determine if the body is in…

A: Given data, Force F1 = 150 N and, F2 = 50 N Force F1 in vector form, F→1= F1-sin45i^+cos45j^ F→1 =…

Q: Consider the following system in static equilibrium. Force vector Facts at a distance" from the pin…

A: (a) Draw the free-body diagram of bar.

Q: The mass center G of the 1220-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: Two uniform rods each with a mass m and length l are attached to gears as shown. For the range 0…

A: Given data: The mass of the rods is m. The length of the rod is l. The angle of rod AB from…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.