2. A rectangular plate 4X8 in. is in full contact with the base of a fixture. The hole in the workpiece has been machined to 1.500 in. at the exact center of the plate. Figure 2 shows this plate. The plug diameter is 1.495. Calculate: a) the maximum height of the plug if the 4-in. side is lifted of the plug, and b) the maximum height of the plug if the 8-in. side is lifted off the plug. c) Compare the two plug designs.

2. A rectangular plate 4X8 in. is in full contact with the base of a fixture. The hole in the workpiece has been machined to 1.500 in. at the exact center of the plate. Figure 2 shows this plate. The plug diameter is 1.495. Calculate: a) the maximum height of the plug if the 4-in. side is lifted of the plug, and b) the maximum height of the plug if the 8-in. side is lifted off the plug. c) Compare the two plug designs.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a) locate the centroid of area given in figure b) calculate the second moments of area give in problem
Draw a common tangent to two circles of diameter 6cm and 4cm respectively if the distance between their centers is 12cm
%3D Consider for the part in the figure below, a =112, b= 60 and c= 104. b. b 40 80 20 45 Dimensions in mm Analyze the part in order to calculate the coordinates of the centre of gravity in the (z, y, z) system of coordinates. It is essumed that the following process was following for the manufacturing process • Part 1(a cubic piece of dimension 37 x 60 x 60 is cut out of a Part 2 of dimensions 149 x 60 x 80 and then • Part 3 (triangular prism) is welded Part 2
Solve correctly
Find the centroid of the plate shown in figure. Where B = 95 mm, b= 18 mm, d =54 mm, y = 15mm (ENTER ONLY THE VALUES IN THE BOXES BY REFERING THE UNITS GIVEN IN THE BRACKET) B (i) The Area of full Triangle (unit in mm2) is =,
Calculate the outer diameter using compound method if the minor diameter is 28mm. angle of taper is 80.The total length of work piece is 120mm and the taper length is 80mm. Also draw the diagram and label the dimensions.
1. A 5 in diameter solid shaft is used to drive the propeller of a marine vessel. It is necessary to reduce the weight of the shaft by 60%. What would be the dimensions of a hollow shaft in mm if made of the same material as the solid shaft?
5 The best size wire is fitted in a groove of a metric screw such that the wire touches the flanks of the thread on the pitch line as shown in the figure. The pitch (p) and included angle of the thread are 4 mm and 60°, respectively. The diameter of the best size wire is mm (round off to 2 decimal places). Pitch line Flank 60⁰ Wire 0.25p -0.5p-
Draw the free body diagrams for each part in the figures below:
4c needs to be done
I need the answer as soon as possible
Required information Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has a 1.250-inch-thick bar that needs 90° grooves machined into it for precision ground 1.0000-inch diameter cylinders. A sine bar is used by placing different thicknesses under one of the cylinders so that the proper angle is attained. Sally wants the distance between the centers of the cylinders to be D= 5.9 inches. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 7 -1.00000 * How deep should she mill the 90° grooves so that the top of the sine block is 2 inches tall? (Round the final answer to four decimal places.) The depth of the mill should be 7071.067 inches.