question 3 solution only A d.c. 2-wire ring main ABCDEA is fedfrom 230 V supply as shown in Fig. 13.46.The resistance of each section (go and re-turn) AB, BC, CD, DE and EA is 0-1 W.The loads are tapped off as shown. Findthe voltage at each load point.IV3 = 227 V; Vc-225 V ; V,= 225 V ;VE- 226 V|In the d.c. network shown inFig.13.47, A is the feeding point andis maintained at 250 V. The resistances2.+ 12 A0.4 236 AA0.8 216 A0.4 23.8 ADFig. 13.47of the various branches (go and return) are indicated in the figure. Determine the current in eachbranch.JAB - 144A ; BC - 2A ; DC - SA ; AD- 13A|0.8 2B,0.4 2

apply KVL in loop (1)0.4 I1 +0.8(I1-12) - 0.8 I2=00.4 I1 +0.8 I1-0.8 I2 = 9.61.2 I1 -0.8 I2 =9.6…

2. A d.c. 2-wire ring main ABCDEA is fed from 230 V supply as shown in Fig. 13.46. The resistance of each section (go and re- turn) AB, BC, CD, DE and EA is 0-1 W. The loads are tapped off as shown. Find the voltage at each load point. IV- 227 V; Vc-225 v ; V,- 225 V; VE= 226 V| 3. In the d.c. network shown in B. 12 A 0.4 2 36 A A 0.8 Q 16 A 0.4 2 +8 A Fig.13.47, A is the feeding point and is maintained at 250 V. The resistances Fig. 13.47 of the various branches (go and return) are indicated in the figure. Determine the current in each branch. |AB = 144A ; BC = 2A ; DC = 5A ; AD - 13A| 0.8 2 0.4 2

2. A d.c. 2-wire ring main ABCDEA is fed from 230 V supply as shown in Fig. 13.46. The resistance of each section (go and re- turn) AB, BC, CD, DE and EA is 0-1 W. The loads are tapped off as shown. Find the voltage at each load point. IV- 227 V; Vc-225 v ; V,- 225 V; VE= 226 V| 3. In the d.c. network shown in B. 12 A 0.4 2 36 A A 0.8 Q 16 A 0.4 2 +8 A Fig.13.47, A is the feeding point and is maintained at 250 V. The resistances Fig. 13.47 of the various branches (go and return) are indicated in the figure. Determine the current in each branch. |AB = 144A ; BC = 2A ; DC = 5A ; AD - 13A| 0.8 2 0.4 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Include an illustration of the circuit in the solutions. Thank you
Answer question 13 to 15 please.
O pA:YY 40 docs.google.com/forms/d/e, Q1: Choose the correct answer for the following: 3- For a (1 k2) copper composition resistor with a temperature coefficient at (20°C) 0.00393, determine the resistance at (80°C) ? * 1.24 Q O 1.42 Q 1.44 Q This is a required question 7-What is the relative increase or decrease in conductivity of a conductor if the area is increasing by (30%) and the length is decreasing by (40%) ? The resistivity is fixed. * G2 =2.1667 G1
What is the main difference between a semiconductor and an insulator? a)An insulator contains no electrons in the valence band. b)An insulator has a much smaller band gap than a semiconductor. c)An insulator has a much larger band gap than a semiconductor. d)An insulator contains no electrons. Previous QuestionPreviousNext QuestionNext
TII 5.) A 5.5 mm2 THHN Cu Wire will have this ampacity if it is used at an ambient temperature of 36⁰C. A. 8.0 B. 14 C. 22 D. Either B or C
Subject: Engineering Electronics In 150 words or more: Kindly answer the question in essay form. Explain why an n-type semiconductor material is electrically neutral and not negatively charged. Subiect: Engineering Electronics
Quick please.
A series circuit is set up with an AA battery along with an mystery material and ammeter; however, there’s no current passing through. A.Insulator B.Conductor C.Semiconductor
What unit of measurement is used for fhe diameter of fhe wires
Match The following. Energy derived from organic waste Choose. Energy from interior of earth Choose.
Problem 3: A factory manufactures a specific copper part. It is found at a certain temperature the resistance in m2 of this part is normally distributed with mean of 23.8 and standard deviation of 1.23. Among 5000 units of such parts, how many units are likely to have a resistance (a) less than 23? (b) greater than 24? (c) between 24.2 and 24.5?
Determine ♡ 1) VR 2. Q KZ VR