2. A cut slope is to be made as shown. The unit weight of soil is 18KN/cu.m and the angle of internal friction is 22°. The soil has cohesion of 30 Kpa. The cut slope makes an angle of 30° with the horizontal and the height is 12 m. If the failure plane is 15° from horizontal. Determine a. Frictional force along the failure plane b. Cohesive force along the failure plane Factor of safety against sliding B 24 m A trial failure plane 12 m 30 15° C

2. A cut slope is to be made as shown. The unit weight of soil is 18KN/cu.m and the angle of internal friction is 22°. The soil has cohesion of 30 Kpa. The cut slope makes an angle of 30° with the horizontal and the height is 12 m. If the failure plane is 15° from horizontal. Determine a. Frictional force along the failure plane b. Cohesive force along the failure plane Factor of safety against sliding B 24 m A trial failure plane 12 m 30 15° C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the determination of earth pressure, Coulomb's wedge theory assumes that (A)the back of wall is smooth and vertical. (B) the soil is non-homogeneous and anisotropic. (C) the slip surface is circular. (D)the wall surface is rough.
By using the yield line theory, find the value of uniformly load (w) of the Isotropic slab, take negative m- = 31 kN.m and positive m+ = 20 kN.m. ше 4m 4m ws 3m
A cut is made into a homogeneous soil as depicted in the figure below, at an angle of 60° with the horizontal. Calculate the resisting shear force in kN along the failure plane given that the shear force applied by the overlying soil wedge is 120 kN. The failure plane is at an angle of 40° from the horizontal direction and the ground water level is below this plane. Assume drained conditions for this question.
20. A 17-m thick soil has water table 4 m. below the ground surface. The soil has a void ratio of 0.53 and specific gravity of 2.65. Above the water table, the soil has a degree of saturation equal to 40.67%. Direct shear test conducted on the soil shows that the an angle of internal friction of 26.04° and cohesion of 17.17 kPa. What is the potential shear strength (in kPa) on a horizontal plane at a depth of 9 m. below the ground surface? Round off to two decimal places.
Geotechnical engineering
(1b) Estimate the settlement of a 10 m square area loaded 1 m at 100 kN/ m3 placed 1 m below ground level with ground water at the level of the footing. The static cone resistance values for the sand deposit are as follows: G.L to 6 m = 8000kN/m3,6 -11 mm = 10,000kN/, below 11 m =12,000kN/m3.
Question 1: You are designing a retaining wall at the construction site. The friction angle of sand backfill is 28". Define the active lateral earth pressure coefficient based on Rankine's theory. Show your work and select the closest value: a) 0.30 b) 0.35 c) 0.40 d) 0.50
Please solve and provide answers
A 10 m high sope of dry clay sol (unil weight = 20 N/m) with a slope angle of 45 and the circular slip suriace, is shown in the figure (not drawn to the scale). The weight of the slp wedge is denoted by W. The undrained unt cohosion (C) is 60 kPa. 10m Unit weight= 20 kN m C = 60 kPa 10m 448m, 45% The facter of safety of the slooe against sip failure. IS
1. The following is a sketch of the proposed embankment, calculate the addition of vertical stress (Bousinesq method / graph below) at the depths of points A and B. Assume the unit weight of the soil stockpile = 20 kN / m3. 2. Calculate the added vertical stress at points A and B as deep as Z = 8 m, under the rectangular load
I need the answer quickly
For the footing plan shown in Figure, calculate the increase in vertical stress in point A under the footing with depth of 3 meters, q = 200 kN/m2. R1=1 m RI B 3. 4.