2. A concrete column and cantilever beam as shownPBImThe known loads:PD = 600 kNP₁ = 400 KNfc' = 30 Mpafy = 420 MpaProblems:Find the longitudinal reinforcement for column (assume short column).

Given; PD = 600 KN PL = 400 KN fc' = 30 Mpa fy = 420 Mpa

2. A concrete column and cantilever beam as shown P lm The known loads: = 600 kN Pp PL = 400 KN fc' = 30 Mpa fy = 420 Mpa Problems: Find the longitudinal reinforcement for column (assume short column).

2. A concrete column and cantilever beam as shown P lm The known loads: = 600 kN Pp PL = 400 KN fc' = 30 Mpa fy = 420 Mpa Problems: Find the longitudinal reinforcement for column (assume short column).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam has a width of 300mm and an effective depth of 537.50 mm to the centroid of tension steel bars. Tension reinforcement consists of 6 - 28mm dia in two rows, compression reinforcement consists of 2 - 22mm dia, fc' = 27.6MPa, fy = 414.7MPa, d' = 60mm, L = 4m, the Unit weight of concrete is 24.56kN/cu.m If the beam is simply supported carrying a uniformly distributed dead load of 10kN/m, a uniformly distributed live load of 5kN/m, the safe concentrated live load that it could carry acting at the midspan is _________kN. IS 456:2000
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the tensile steel ratio for positive bending. 2. Determine the depth of the uniform rectangular stress block on the beam section at ultimate stage when subject to positive bending. 3. Determine the design moment capacity in kN•m of the beam in positive bending.
I need a solution quickly, Use ACI Code
Ultimate Design Single concrete
Given a rectangular section of b = 300mm, h = 400mm, a, = a', = 40mm; the concrete is of grade C30, the steel is HRB400. Find the reinforcement (A, and A') required for a load of M = 218kNm and an axial compression N= 396KN. %3D
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the maximum steel ratio if the beam is singly reinforced in negative bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only. 2. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.005 upon crushing of concrete. Write the answer in 5 decimal places only.
5. The beam shown is reinforced for positive moment with three epoxy-coated #11 bars. The bars terminate at the center of the supports. Neglecting beam weight (concentrated loads are very heavy), determine if the required development length is satisfied. Assume As required = 4.55in², 2 in. clear cover on all sides of the longitudinal reinforcement, normal weight concrete, #3 stirrups @12 in o.c., f'c = 5000 psi and fy = 60,000 psi. 8 ft | Pu 20 ft Pu 8 ft ge2 of 56 30 in b=14in. ed 5/15/2020 As = 3-#11
A beam has a width of 280 mm and 490 mm overall depth. Concrete cover is 65 mm from the centroid of bars. Concrete compressive fc' = 24 MPa. Steel yield strength are fy=415 MPa and fy = 275 MPa for ties. Determine the shear strength provided by concrete using simplified method a) If the beam is subjected to shear and flexure only, and b) If the beam is subjected to axial compressive force of 124kN.
A reinforced concrete beam that is 375 mm wide and 500mm deep must resist a service live load moment of 250 kN-m and a service dead load moment of 150 kN-m. Use f'c-21 MPa and fy=415 MPa. The effective concrete cover is 65mm (to the centroid of reinforcements). 1. Determine the area of compression steel reinforcement (If required. Answer O if not) in mm² 2. Determine the minimum number of 25 mm diameter bars to be provided to satisfy the demand ultimate moment 3. Determine the maximum number of 25 mm diameter bars to be provided to have a tension controlled section Answer 1: 2403.21 correct answer: Answer 2: 9.00 Answer 3: 8.00
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
Given are the following: 300 Unit weight of concrete = 24 kN/m3 f'c = 28 Mpa fpe = 850 MPa fpu = 1350 MPa Aps = 750 mm? foy = 1280 MPa Beam is a simple span and have a length of 24m. Use bonded tendons as prestressed reinforcement. A. Determine the value of fps (MPa) B. Determine the nominal moment strength (kN-m) 750 850
Use USD method.