Answered: 2. A block of mass 2 kg strikes a… | bartleby

Related questions

Question

please include a step by step explanation along with the what variables are given what formulas to use and why

2. A block of mass 2 kg strikes a horizontal spring with a speed of 1.5 m/s. It compresses the spring a max amount of
0.1m. How long will the block be in contact with the spring? Assume it loses contact at equilibrium.

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A cannon is turned towards the west and a cannonball is fired. This cannonball has a velocity of 252 kmph at an angle 60 degrees. The cannonball lands on a hillside 100 metres above its starting level. What is the range of the cannon ball? Make a simple sketch. Make a list of all given values, units, and the variables they represent. write the general form of the equation you are going to use. Insert the known values and solve. State at the start of the problem which direction is positive by using an up or down arrow. Keep the velocity components and time to 2 decimal places.
Show your step by step solutions. 6. With a wooden ruler, you measure the length of a rectangular piece of sheet metal to be 16 mm. With micrometer calipers, you measure the width of the rectangle to be 5.98 mm. Consider 4 significant figures only. Determine: (a) the area of the rectangle; (b) the ratio of the rectangle's width to its length; (c) the perimeter of the rectangle;
Provide your calculations, including all relevant steps are included and your units are labeled. The plane carrying the supplies will be cruising at a constant velocity of 250 miles per hour relative to the ground and at a height of 2,650 meters above the target site. Using this information, create a supply drop plan including all required information and calculations outlined below. As you are completing your supply drop plan, remember that correct SI units are a required component of your calculations and descriptions. A) Provide your calculations, including all relevant steps are included and your units are labeled. B) Describe the components of the kinematics equations used in your initial calculations below.
A group collected data in an experiment to learn to draw suitable trendline in a graph. They don't know the theoretical model, so they are trying to determine one through this experiment. They used Excel to display the data and to find good fit. They tried linear, exponential, and power trendlines. The result of each trial is shown below. The title of the plot contains the name of the trendline used to fit. What should be their analysis based on the result they have so far? Exponential trendline 20 Power trendline 18 y = 0.8374e047x R? = 0.9851 16 y = 0.8045x1.538. R2 = 0.981 15 14 12 10 10 ..... 4 ..... ....... 2 1 3 4 1 7 Linear trendline 20 y = 3.0209x - 4.6606 15 R? = 0.9293 10 ........ 2 4 6 8 The linear trendline is good fit The exponential trendline is good fit Any one of the three trendlines seems good candidate The power trendline is the best fit 2. 2.
A group of students wish to determine, experimentally, the bulk density of an unknown material. To determine this amount, the students measured the diameter, height, and mass of various cylinders. These values appear in the table below. Determine: a) The volume of the cylinders that appears in the following table. b) The graph of mass vs. volume.
I need help with knowing what to cirlce. The " increases decreases" part.
A. Solve the problems below. You are required to show the proper solution with the final answer written inside a box. Make sure to put the final unit of measurement.
I recently asked this question, but the answers are not loading. I don't understand part a, and the formulas used. I guess I don't understand how to derive the formulas into what you need. Could you explain, step by step?