2. a) 25mL of water is added to 125mL of 1 0.15mol/L NAOH solution, what is the concentration of the diluted solution? b) What volume of 0.05mol/L HC1 solution is made by diluting 250mL of 10.0mol/L HC1?

2. a) 25mL of water is added to 125mL of 1 0.15mol/L NAOH solution, what is the concentration of the diluted solution? b) What volume of 0.05mol/L HC1 solution is made by diluting 250mL of 10.0mol/L HC1?

Chemistry: Matter and Change

1st Edition

ISBN:9780078746376

Author:Dinah Zike, Laurel Dingrando, Nicholas Hainen, Cheryl Wistrom

Publisher:Dinah Zike, Laurel Dingrando, Nicholas Hainen, Cheryl Wistrom

Chapter16: Reaction Rates

Section: Chapter Questions

Problem 5STP

See similar textbooks

Similar questions

When you heat water on a stove, small bubbles appear long before the water begins to boil. What are they? Explain why they appear.
The freezing point of a 0.11 m solution of HNO2 is -0.20C. (a) What is i for the solution? (b) Is the solution made (i) of HNO2 molecules only? (ii) of H+ and NO2- only? (iii) of more HNO2 molecules than H+ ions? (iv) primarily of H+ and NO2- ions with some HNO2 molecules?
Supersaturated solutions of most solids in water are prepared by cooling saturated solutions. Supersaturated solutions of most gases in water are prepared by heating saturated solutions. Explain the reasons for the difference in the two procedures.
Graph Table 14.10 shows solubility data that was collectedin an experiment. Plot a graph of the molarity ofKI versus temperature. What is the solubility of KI at55°C?
Consider three test tubes. Tube A has pure water. Tube B has an aqueous 1.0 m solution of ethanol, C2H5OH. Tube C has an aqueous 1.0 m solution of NaCl. Which of the following statements are true? (Assume that for these solutions 1.0m=1.0M.) (a) The vapor pressure of the solvent over tube A is greater than the solvent pressure over tube B. (b) The freezing point of the solution in tube B is higher than the freezing point of the solution in tube A. (c) The freezing point of the solution in tube B is higher than the freezing point of the solution in tube C. (d) The boiling point of the solution in tube B is higher than the boiling point of the solution in tube C. (e) The osmotic pressure of the solution in tube B is greater than the osmotic pressure of the solution in tube C.
A patient has a “cholesterol count” of 214. Like manyblood-chemistry measurements,this result is measured inunits of milligrams per deciliter (mgdL1). Determine the molar concentration of cholesterol inthis patient’s blood, taking the molar mass of cholesterolto be 386.64gmol1. Estimate the molality of cholesterol in the patient’sblood. If 214 is a typical cholesterol reading among men inthe United States, determine the volume of such bloodrequired to furnish 8.10 g of cholesterol.
The Henry's law constant for the solubility of argon gas in water is 1.0103M/atm at 30C. (a) Express the constant in M/mm Hg. (b) If the partial pressure of argon gas at 30C is 693 mm Hg, what is the concentration (in M) of the dissolved argon gas at 30C? (c) How many grams of argon gas can be dissolved in 29 L of water at 693 mm Hg and 30C? (Ignore the partial pressure of water.)
One mole of Na2S is represented as where represents Na and represents S. Complete the picture showing only the sodium and sulfide ions. The water molecules need not be shown. What is the molarity of Na+? of S2-?
What happens if you add a very small amount of solid salt (NaCl) to each beaker described below? Include a statement comparing the amount of solid eventually found in the beaker with the amount you added: a a beaker containing saturated NaCl solution, b a beaker with unsaturated NaCl solution, c a beaker containing supersaturated NaCl solution. A saturated sodium chloride solution.
Addition of water to concentrated sulfuric acid is dangerous because it generates enough heat to boil the water, causing it to spatter out of the container. For this reason, chemists remember to add acid to water. In a dilution experiment, we calculate the amount of the more concentrated solution that must be measured out. If we place this concentrated solution (Figure 4.7) in the volumetric flask first, then dilute with water, we violate the caution Add acid to water. Describe a safer variation on the method shown in Figure 4.7 that allows the quantitative dilution of concentrated sulfuric acid. Figure 4.7 Preparing a dilute solution from a concentrated solution. (a) Draw the concentrated solution into a pipet to a level just above the calibration mark. (b) Allow the liquid to settle down to the calibration line. Touch the tip of the pipet to the side of the container to remove any extra liquid. (c) Transfer this solution to a volumetric flask. Again touch the pipet to the wall of the flask to ensure complete transfer, but do not blow out the pipet because it is calibrated for a small amount of liquid to remain in the tip. (d) Dilute to the mark with solvent. Frequently, especially with concentrated acids, it is best to have some solvent present in the volumetric flask before you add the concentrated sample.
Stock solutions of HCl with various molarities are frequentlyprepared. Complete Table 14.7 by calculatingthe volume of concentrated, or 12M, hydrochloric acidthat should be used to make 1.0 L of HCl solution witheach molarity listed.
The following diagrams show varying amounts of the same solute (the red spheres) in varying amounts of solution. a. In which of the diagrams is the solution concentration the largest? b. In which two of the diagrams are the solution concentrations the same?