2. A 10-x 10-mm key was used in a 45-mm diameter shaft of a 30 kW diesel engine rotating at 1200 rpm. Calculate the shear stress in the key and the torsional stress in the shaft. Assuming length of key to be 1.5 times shaft

2. A 10-x 10-mm key was used in a 45-mm diameter shaft of a 30 kW diesel engine rotating at 1200 rpm. Calculate the shear stress in the key and the torsional stress in the shaft. Assuming length of key to be 1.5 times shaft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: e diameter

A: To find Outside diameter(d2)

Q: The nature of the stresses

A: Given; A helical gear with pressure angle,α= 200 and β=300 helix angleAt the mid span of a shaft is…

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: Design and draw a neat sketch of a cast iron protective type flange coupling to transmit “P” kW at…

Q: A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is…

A: To design: The bushed pin coupling. Given: The power transmitted is P=10 kW103 W1 kW=10×103 W. The…

Q: Problem 2: A solid circular drive shaft with a diameter of 0.5" transmits a torque of 200 in-1bf and…

A: The diameter of the shaft, Transmitted torque, The maximum bending moment, The yield strength of…

Q: A UNS G10350 steel shaft, heat-treated to a minimum yield strength of 75 kpsi, has a diameter of 1-…

A: given data; ⇒minimum yield strenth (ys)=75kpsi⇔517.107MPa⇒diameter(D)=1716in=1.437in⇔36.49mm⇒speed…

Q: pot

Q: An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter…

Q: Compute the twisting and bending moments of the shaft (AISI 4140 steel) given the following…

Q: PROBLEM 2 A drive shaft running at 2500 rpm has outer diameter of 80mm and inner diameter of 60mm.…

Q: Q2. A compound shaft supports five pulleys that transmit different amount of torques as shown in…

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

Q: The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley…

A: diameter of pulley (d) = 110 mm no of belt = n = 2 groove angle = 2β = 45° = β = 22.5° power…

Q: A UNS G10350 steel shaft, heat-treated to a minimum yield strength of 75 kpsi, has a diameter of 1-…

A: Power is given by P =( T * n )/63025 T = F*D/2 Ssy = 0.577*Sy ( distortion energy theory)

Q: Design a muff coupling to connect two shafts. The power to be transmitted is 27kW at a shaft speed…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

Q: A hollow tubular component is made of Steel having a Young's modulus of 205 GPa and yield strength…

A: Given Data⇒ Tensile load (F)=38 KN External diameter of the hollow tubular component is d2=45 mm…

Q: A hollow circular cold-rolled bronze [G1 - 6200 ksi] tube (1) with an outside diameter of 1.75 in.…

Q: Figure below shows a portion of a pump that is gear-driven at uniform load and speed. The 25 mm…

Q: Design and draw a neat sketch of a cast iron protective type flange coupling to transmit “P” kW at…

Q: A gear transmits 560 N of torque to a circular shaft having a diameter of 58 mm. A square key 13 mm…

A: Given Data The diameter of the shaft is: d=58 mm The torque transmitted by the gear is: T=560 N·mm…

Q: Estimate the shaft diameter required to produce a critical speed of rotation of 638 rpm for a steel…

Q: Torque =230 N-m

A: The torque for designing a rigid flange couple is given as, T=250 N-mT=250×103 N-mm The number of…

Q: shaft transmits 75 kW power at 300 r.p.m. The distance between the two bearing is 3000 mm. It is…

Q: A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum…

A: Given, Length of shaft = L = 1 m Power transmitted = P = 30 kW = 30 x 103 W Shaft RPM = 700 rpm…

Q: proper key for the joint shown in figure E rque of T= 180 N.m. The hub has length of

A: Given data shaft dia = 30 mm length of hub = 50 mm allowable compressive stress = 120 MPa Required =…

Q: 5.2 A hollow bronze shaft of 75 mm outside diameter and 12.5 mm thick is coaXlal WiU. solid steel…

A: Outer diameter, Do=75 mmInner diameter, Di=50 mmDiameter of steel shaft, D=50 mmT=5693 N.m Note:…

Q: A motor provides 60 hp power to a wheel B. It rotates a solid shaft in AISI 1020 steel, 4 cm in…

Q: . Determine: the diameter of shaft

A: Given: P= 20 kW N=750 rpm T1/T2=2.5 WA=300 N WB=250 Nshear stress=70 MPa kt=2 km=1.5 DB=1000 mm…

Q: A 1018 steel wedge will be created with Sy = 63 Kpsi and a factor of safety of 1.5. The axis where…

Q: Describe the failure of a hollow torque tube. Calculate the forces creating the failure

A: It is asked to describe the failure in the hollow torque tube

Q: m. Design a cast Iron flange coupling for the shaft. The allowable stresses are Shear stress for the…

Q: A solid 2 inch diameter bar is experiencing a torque of 3000 in-lb. The material of the bar has a…

A: Torsional Shear Stress Calculation:The first step is to calculate the torsional shear stress in the…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

2. A 10-x 10-mm key was used in a 45-mm diameter shaft of a 30 kW diesel
engine rotating at 1200 rpm. Calculate the shear stress in the key and the
torsional stress in the shaft. Assuming length of key to be 1.5 times shaft
diameter.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1½

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A shaft has a diameter of 45.08 mm and is an interference fit with a sleeve 60 mm outer, 45 mm inner 45 mm inner diameters and 80 mm long. Calculate: i. The force needed to slide the sleeve on the shaft, and ii. the change in radius of the shaft and sleeve at the inside. Assume the elastic properties for both are the same with Young's modulus of elasticity as 200 GPa and Poisson's ratio of 0.3.
A shaft/hub connection transmits a torque C =60N.m. We use a rectangular key (W=14mm x H=9mm) with a length of 30mm for a 45mm diameter shaft. Calculate the force exerted on the key.Calculate the compressive and shear stress.
A gear drive is required to transmit a maximum power of 22.5KW, the velocity ratio is 1:2 and the rpm of the pinion is 200 .the approximate center distance between the shaft may be taken as 600mm.the teeth has 20°stub involute profile.the static stress for the gear material ( which is cast iron ) may be taken as 60MPa and face width as 10 times the module.find the module, face width and number of teeth on each gear.Check the design for dynamic and wear loads. The deformation factor in the buckling equation may be taken as 80 and material combination factor for the wear as 1.4
A 16 in. diameter motor pulley is running at 600 rpm with a 6 in diameter shaft transmitting power to an agricultural locomotive. If the dimensions of the square key is 0.5 x 3 in, what is the maximum force in the pulley’s belt that can be transmitted if the shear stress is limited to 8500 psi and bearing stress limited to 4000 psi?
Bearing stress 2. Please provide proper discussion and illustration also complete solution and clear solution please thank you. Determine the length of a square key to be used for a 3.73 kW 1800 rpm electric motor. Motor shaft diameter is 35 mm and the height of the key is approximately one-half of the shaft size. The bearing stress on the key is?
Design the size of a solid shaft for a 500 hp, 250 rpm if the allowable torsional deflection is 1 degree. Use C1045 as rolled steel for medium shock loading.
Please design the following mechanical shaft targeting design objective of reliable structure and performance via design iterations with constrains of geometrical dimensions within performance requirement, safety, and economic factors (finding minimum material cost of suitable diameter). Notes: This shaft is transmitting 200 kW at 1200RPM. Please design the shaft with a suitable diameter via iterations, if the maximum torque transmitted exceeds the mean by 30%. Take maximum allowable shear stress as 70 MPa.
Within Hour Please.
A square key fixing a gear on a 30 mm diameter shaft. The shaft is transmitting a power of 18 kW to the gear at 800 rpm. The key is made of steel with a yield strength of 470 N/mm² and the factor of safety is 2.5. The yield strength of the key material in compression can be assumed to be equal to the yield strength in tension. Determine the dimensions of the key.
with diameter d = 38 mm transmits 37 kW to a gear Calculate the required speed of rotation (number of at B. The allowable shear stress in the steel is 40 MPa. X7-3 A motor driving a solid circular steel shaft revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit. Motor d = 38 mm B
The disc clutch of an automobile is carried on a 2-inch 6-splined shaft and not to slide under load. The nominal dimensions are as follows: b = 0.25 D; t = 0.075 D and d = 0.85 D. The hub length of 150 % of shaft diameter. Determine the total horsepower transmitted at 3,600 rpm, if the yield strength of the shaft is 1,400 psi