2: You want to move your 25-kg spare tire from the floor onto the back of your pickuptruck. The bed of your truck is 0.83 meters above the floor. You have found a sturdy rope, and a strongplank to use as a ramp that is 2.8 meters long. The coefficient of kinetic friction between the tire and theplank is μk.h Case 1friction.Case 2Case 3a) What is the minimum work in joules you will do in rolling the tire all the way up the ramp as shown in Case (1)? Neglect any losses due toCalculate the size of the average force in newtons that you must apply on the tire if you push in a direction parallel to the ramp? See Case (1).After a few unsuccessful tries, your friend suggests that you push the tire up the ramp by applying a horizontal force, as shown in Case (2).Calculate the work in joules you will (hopefully) do in moving the tire up the ramp this way. Again, neglect any frictional losses.See Case (2).Calculate the size of the average force in newtons that you must apply on the tire if you push horizontally to roll it up the ramp.In yet another desperate attempt, you think perhaps that it will be easier to pull the tire up the ramp. You put the tire on the ramp, tie your sturdyrope to the tire, and pull on the rope parallel to the ramp, as shown in Case 3. Calculate the work in joules you will (hopefully) do in moving the tire up the ramp thisway given μk = 0.335

Answered: Image /qna-images/answer/09533606-5ebc-45bd-9306-ec5881b4e8ab.jpg

Answered: 2: You want to move your 25-kg spare…

Similar questions

a. Calculate the work done (in J) on a 1550 kg elevator car by its cable to lift it 39.5 m at constant speed, assuming friction averages 135 N. b. What is the work done (in J) on the lift by the gravitational force in this process? c. What is the total work done (in J) on the lift?
1. How much work was done by a machine that exerts a 5000 N force to compress a 10-meter-long steel bar so it becomes 3 meters in length. 2. Find the angle between the 500 N applied force and the 3-meter displacement if the work done is 1500 Joules. Hiii please write a solution thank you
A 2.46 kg block moves along a frictionless surface with a speed of 7.83 m/s when it encounters a rough shallow hill, whose sides have a length of l=5.21 m. The hill is low enough so that the block can make it over the hill. Because the surface of the hill is rough (shown in orange in the figure), the block experiences a frictional force of 2.23 N while on the hill. a) What is the speed of the block after it traverses the hill?
A horizontal force of 150 N is applied to push a 40.0 kg box a distance 6.00 m on a rough horizontal surface. If the box moves quickly constant, determine: A. The work that reverses the 150 N force. B. The coefficient of kinetic friction between the box and the surface.
A box slides down a plank of length d that makes an angle of θ with the horizontal as shown. μk is the kinetic coefficient of friction and μs is the static coefficient of friction. 1.Enter an expression for the minimum angle θ (in degrees) the box will begin to slide. 2.Enter an expression for the nonconservative work done by kinetic friction as the block slides down the plank. Assume the box starts from rest and θ is large enough that it will move down the plank. 3.For a plank of any length, at what angle θ (in degrees) will the final speed of the box at the bottom of the plank be 0.85 times the final speed of the box when there is no friction present? Assume μk = 0.39.
Block B is stacked on top of block A and does not slide with respect to A below – the blocks move as a single unit. The blocks slide to the right on a horizontal surface of uniform roughness while a tension force is applied to block A horizontally to the right. The blocks move a distance d and are speeding up. The work that B does on A is __________. a. Zero b. The magnitude of the tension force is needed to determine whether the work is positive, negative, or zero c. The masses of the blocks are needed to determine whether the work is positive, negative, or zero d. Negative e. Positive ------------------------------------------------------------------------------------------------------------- 2 The total work on A is __________. a. Negative b. The masses of the blocks are needed to determine whether the work is positive, negative, or zero c. Zero d. The magnitude of the tension force is needed to determine whether the work is positive,…
A box is pulled 2.0 meters along a rough surface at constant velocity using 100 N force inclined at 30° above the horizontal. a.If the force applied, Fa is doubled but the frictional force remains the same (this is unlikely to occur in practice since normal force changes), will the net work be the same? b. Is Fa is doubled with the frictional force unchanged how much kinetic energy would the block have after being pulled 2.0 m?
A yoyo of radius R and mass M is released from rest with the string vertical and its top end fixed up a support as shown below. How fast is the center of mass of the yoyo moving when it has fallen a distance of 47 cm. Ignore the mass of the string and express your answer if m/s
1. A 7.50-kg box initially at rest slides down a 15.0 m long incline that makes an angle of 22.0° with the horizontal (see figure). At the bottom of the incline, the speed of the box is 3.00 m/s. a) Draw a free body diagram, detailing all of the forces acting on the box. b) Using the work done by non-conservative forces relationship, find the algebraic expression for the coefficient of kinetic friction between the box and the incline. c) Calculate the coefficient of kinetic friction.
A 1300 kg wrecking ball hangs from a 10-m-long cable. The ball is pulled back until the cable makes an angle of 17.0 with the vertical. ▼ Part A By how much has the gravitational potential energy of the ball changed? Express your answer with the appropriate units. AU = 0 μA Value = Units ?
A. Calculate the work done by the force of gravity when a 5.0kg object is lifted to a height of 30.0m above the ground B. Calculate the velocity with which the object strikes the ground if dropped from that height, using the principle of conservation of energy C. Calculate the kinetic energy and the potential energy of the object at a halfway on the path after it is dropped. To do this part, you need to find the velocity of the object at that position using an equation of motion. What is the total energy of the object at that point? Does this verify the principle of conservation of energy?
In the Figure below, we see a 500 gram block resting on the horizontal portion of a "track", whose left end is curved upwards. The horizontal portion of the track is frictionless, except for a 50.0 cm long “rough" portion, shown in the Figure, where the coefficient of kinetic friction is 0.300. The curved portion of the track is frictionless. The block is held against a spring (which has a stiffness constant of 500 N/m), compressing the spring by 10.0 cm. Then the block is released from rest. (NOTE: The block is not attached to the spring; it is just held against the end of the spring.) For simplicity, assume that g = 9.80 m/2. 50.0 cm

SEE MORE QUESTIONS