Answer 2 The steady-state error is smaller than 1%, and the settling time and overshootrequirements have been met. As you can see, the design process for root locus is verymuch a trial and error process. That is why it is nice to plot the root locus, pick thegain, and plot the response all in one step. If we had not been able to get a satisfactoryresponse by choosing the gains, we could have tried a different lag controller, or evenadded a lead controller.Question:1:- What is the advantage of the adding a Lag controller for the SS model?2:- What is the effect of increasing the value gain (K) on the system using theproportional controller?3:- The characteristic equation of linear control system are given as followsConstruct the root locus for Ks'+2s²+(K+2)S+5K=0Drawing the root locus of the system using Matlab Program?

It is given that: proportional controller

Answered: 2:- What is the effect of increasing…

Engineering

Electrical Engineering

2:- What is the effect of increasing the value gain (K) on the system using the proportional controller?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

hi pleasee help me answer this question
Whale and Kanmuro are two islands located at the Chimera archipelago. These two are separated by a distance of 24 miles. A power link is to be established between them. The power link delivers a maximum power of 601 megawatts at full capacity with an operating voltage of 527 kilovolts. Note that 1 mile is 1.5 kilometers. Solve for the current at full power capacity in kiloamperes. Express your final answers to four decimal places
Write an Abstract about Water Level Indicator:
1. Electrical explosions directly into the face of a person working on or near energizedelectrical equipment can and will cause serious injury or death. OSHA laws and NFPA70E have strict safety requirements for working on electrical equipment. The basicrules are to turn off the power before working on the equipment and to wear the propertype of nonflammable clothing. To further provide safety for the worker, the NationalElectrical Code has a requirement pertaining to arc-flash hazard warning. This requirement is found in of the NEC.
A string of suspension consists of four (4) units. The Voltage between each pin and earth is 0.12 of the Self-Capacitance of the unit. The Voltage between the Line Conductor and earth is 135KV. Find the Voltage distribution across each unit and the String Efficiency
The levelised cost of electricity (LCOE) is often used to compare the costs of electricity production from different types of electricity generation plant. Carefully describe the significance of the LCOE and give one advantage and one disadvantage of using this metric to compare plants.
Briefly explain the Vertical integration in electricity regulation
Define the string efficiency and calculate its value for a string of three insulator units 33 kV overhead line if the capacitance of each unit to the earth and line be 20% and 5% of the self-capacitance of the unit. Drive any formula that might be used.
please sir solve these 2 questions, thanks alot
Discussion Questions 1- Draw the important components of a steam power station. 2- What factors are taken into account to select the site of steam power station. 3- State the main parts of a thermal power station, and discuss the function of each part. 4- Draw the important components of a Hydro-Electric power station. 5- What factors are taken into account to select the site of Hydro-Electric power station. 6- Draw the important components of a nuclear power station. 7- What factors are taken into account to select the site of nuclear power station. 8- What do you understand from the load curve and what information are converged by a load curve. 9- Discuss the important points to be taken into consideration while selecting the size and number of units generation. 10- Explain the terms, connected load, load factor, plant use factor, diversity factor.
MECT361 Mechatronics Components and Instrumentation PLEASE GIVE ME THE short answer and wite it by keyword thanks
please answer with explanation.. answer it ASAP..