2: This circuit has reached steady state before the switch opens at time t 0. t= 0 80 Q +. 12 V 500 nF 5 mH 100 Q v() (a) Determine the values of iL(0-), ir(0-), and v(0-) immediately before the switch opens: (b) Determine the value of v(0+) immediately after the switch opens. (c) Determine the expression of iL(t) and v(t) for t>0

2: This circuit has reached steady state before the switch opens at time t 0. t= 0 80 Q +. 12 V 500 nF 5 mH 100 Q v() (a) Determine the values of iL(0-), ir(0-), and v(0-) immediately before the switch opens: (b) Determine the value of v(0+) immediately after the switch opens. (c) Determine the expression of iL(t) and v(t) for t>0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q.35: For the circuit shown in figure beside, the switch has been in position "a" for a long time. At t=0 the switch moved to position "b". Find the capacitor current as a function of time. a 502 1002 502 100n 2LF: 50V 502 100V
Figure (a) and figure (b) illustrate the signal x(t) and w(t). Given the signal p(t) as follows:
(b) Figure Q1(b) shows the step response for a second-order system. Find its peak time and percentage of overshoot. Hence, obtain its transfer function. 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0. 6 10 12 14 16 18 20 22 24 Time (s) Figure Q1(b) Response
Lesson= Second Order Transient Response A 24-V battery is connected in seires with a 1-Henry (inductor), 8-ohms resistor and a 1/16 Farad ( capacitor) with when the switchis turned “on” at t = 0. And then, what will be the value of the current at t = 0.001 sec.
plz explain how this integral is equal to zero ......... plz provide step by step solution
a) A buck converter has an input of 100 V, output current of 10 A with L= 250 µH and C = 100 µF. The duty cycle is 40% with switching frequency of 10 kHz. The circuit operates with continuous inductor current at threshold 4.8 A. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state, determine the following. i. The output voltage. ii. The inductor ripple current. iii. The maximum and minimum value of the inductor current.
Find the differential equation(s) that model the system. Can it be represented by a single differential equation between Vin and Vout?
Needs Complete typed solution with 100 % accuracy.
For the system unit step response shown below where ss = 54 and t = 6 the system can be modelled by a process with pure time delay and a 1st order. Determine the time constant of the approximated 1st order SS 0.63ss- 3t Answer: 60 10t x The correct answer is: 42.00
Q.15: The switch has been in position "a" for a long time. At t=0 the switch is moved to position "b". Use classical method to find the voltage across and current through the capacitor as a function of time? (Ans.: Vc(t)=80[1.25-e 20 b1002 10m H t%3D0S 30V 42 100V 2uF 5000t -5000t (cos5000t+sin5000t)] V & ic(t)=1.6e sin5000t A)
Why is the circuit under damped? Explain.
Please show working out and answer for the below question. You are investigating the electrical testing circuits and find that, in an inductive circuit, the relationship between instantaneous current i (amps) and the time t (secs) is given by: i = 12.5(1-e-t/CR) Determine the time taken for current to rise from 0 to 1.9 amps with resistor value of 220 and capactor value of 0.000008