2] The device shown is used to straighten the frames ofwrecked autos. Determine the tension of each segment ofthe chain, i.c., AB and BC, if the force which the hydrauliccylinder DB exerts on point B is 3.50 kN, as shown.3.50 kN450 mmD400 mm 250 mm

It is assumed that Force in member AB and BC required to straighten the frame. Let θ is the angle…

2] The device shown is used to straighten the frames of wrecked autos. Determine the tension of each segment of the chain, i.e., AB and BC, if the force which the hydraulic cylinder DB exerts on point B is 3.50 kN, as shown. B 3.50 kN 450 mm D A 400 mm 250 mm

2] The device shown is used to straighten the frames of wrecked autos. Determine the tension of each segment of the chain, i.e., AB and BC, if the force which the hydraulic cylinder DB exerts on point B is 3.50 kN, as shown. B 3.50 kN 450 mm D A 400 mm 250 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two cables are tied together at C and loaded as shown. Determine the tension (a) in cable AC, (b) in cable BC
The press shown is used to emboss a small seal at E. Knowing that the vertical component of the force exerted on the seal must be 900 N, determine (a) the required vertical force P,(b) the corresponding reaction at A.
2.1 - please show the complete solution, thanks!
Page 117 3.53 A farmer uses cables and winch pullers B and E to plumb one side of a small barn. If it is known that the sum of the moments about the x axis of the forces exerted by the cables on the barn at points A and D is equal to 4728 lb-ft, determine the magnitude of TDE when TAB = 255 lb. Fig. P3.53 E 1 ft B A 12 ft 1.5 ft 14 ft E F 12 ft X
A freight car is stopped on a track at an angle of 25o to the vertical. The gross weight of the wagon and its load is 36kN and acts at a point 750 mm from the track, in the middle between the two axles. The wagon is supported by a cable 600 mm from the track. Determine the traction on the cable and the reaction on each pair of wheels.
Knowing that the radius of each pulley is 130 mm and neglecting friction, external force is 297 N. Determine the internal forces at Points J and K of the frame shown. Solution: 1. FBD for frame and pulleys together: a. There are b. Sum moment about point c. Sum all the horizonal forces to zero, solve that Ax = = d. Sum all the vertical forces to zero, yield that Ay + By 2. FBD for Member AE: a. There are supports on the frame, they are both c. Thus By b. Sum moment about point = a. There are solve that Bx = d. Sum all the horizontal forces to zero, solve that Ex N; direction is pointing to the 3. FBD for AK to determine the internal forces on K: forces/reactions on the member AE, for a 2D body, this is statically a. There are forces/reactions on the AK; b. Sum axial forces to zero, solve that nominal force FK d. Sum moment about point and note that the tension force in the cable on D is c. Sum tangential forces to zero, solve that shear force VK = 4. FBD for BJ to determine the…
Q1): The cable stays AB and AD help support pole AC. Knowing that the tension is 120 Ib in AB and 40 Ib in AD. Determine the magnitude and the direction of the resultant of the forces exerted by the stays at A. 10 ft B. D 6 ft
4. Determine reactions at A and D of the frame shown. y 4 kN/m 4 kN/m в 1.5 m 2 m 10 kN-m 20 kN 3 m 4m-
Two bolts at A and B are used to move the trunk of a fallen tree. Replace the forces exerted by the ropes with an equivalent wrench and determine (a) the resultant force , (b) the pitch of the wrench, (c) the point where the axis of the wrench intersects the yz plane.
B Knowing that the maximum allowable tension in cables AB and AC is 500 N, determine the magnitude of the largest force P which can be applied at A, and the corresponding angle a. 30° A. 45° C 220 mm 960 mm Three members are pin- connected at A and loaded as 320 mm shown. Determine the force in members AB and AC, and the magnitude of P if the 380 mm force in member AD is 105 N 240 mm B (directed towards D) and Q is 40 N.
Q.3) The cable shown below is supported by two pins at A and B. The maximum cable tension due to the applied forces is 1000 lb. Determine the tensions in all four segments of the cable and the sags of the load points P1, P2, and P3. В 5 ft- 3 ft А. 2 ft 4 ft 6 ft P3 P1 y V P2 300 lb 100 lb 200 lb
5- The device shown is used to straighten the B 3.50 kN frames of wrecked autos. Determine the tension 450 mm D of each segment of the chain, i.e., AB and BC, if the force that the hydraulic cylinder DB exerts on 400 mm 250 mm point B is 3.50 KN, as shown