Problem 2: The beam is held in equilibrium by a roller at A and a pin at B. The beam supportsa uniform distributed load (2 kip/ft) and a concentrated moment (30 kip-ft) at the locationsshown. Use the equation method to solve this problem.2 kip/ftĮ5 ft5 ft30 kip-ft5 ft(a) Derive expressions for V(x) and M(x)in each section of the beam.(b) Use the results from part (a) to drawthe shear force (V) and bendingmoment (M) diagrams for the beam.Clearly label all important values andpoints on the diagrams.

Answered: Image /qna-images/answer/5f0b1013-a7b3-4ec5-9552-d4087f19a174.jpg

2 kip/ft -5 ft Α-Ω 5 ft 30 kip-ft -5 ft B (a) Derive expressions for V(x) and M(x) in each section of the beam. (b) Use the results from part (a) to draw the shear force (V) and bending moment (M) diagrams for the beam. Clearly label all important values and points on the diagrams.

2 kip/ft -5 ft Α-Ω 5 ft 30 kip-ft -5 ft B (a) Derive expressions for V(x) and M(x) in each section of the beam. (b) Use the results from part (a) to draw the shear force (V) and bending moment (M) diagrams for the beam. Clearly label all important values and points on the diagrams.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the beam loaded as shown in the following figure, draw shear force and bending moment diagram and write their equations. Alsowrite values of shear force and bending moment in the diagrams at all change in loading points and the maximum shear and bendingmoments . where A=13kN/m, B=13kN, M=13/6 kN.m, C=13/6m
Shear and bending moment diagram for the following beam
(a) derive equations for the shear force V and the bending momentM for any location in the beam. (Place the origin at point A.)(b) use the derived functions to plot the shear-force and bendingmomentdiagrams for the beam.(c) specify the values for key points on the diagrams.
For the steel beam and loading shown above (A = hinge support, C = Cable) (A) Write the equations for bending moment and shear force at any section along the beam and draw the shear force and bending moment diagram. (B) Assume a rectangular beam cross section of 25 x 25 mm, what is the maximum bending stress
The Figure shows a loading set up similar to that of the 'Bending in Beams' laboratory experiment. E = 200 GNm"2 and I = 2 x 109 m“. The bending moment and the radius of curvature at any point in the beam between the support points B and C are respectively: 1 kN 1 kN B 0.125 m 1.25 m O a. (-)125 Nm, 1.2 m O b.(-)12.5 kNm, 2.8 m O C. (-)2.5 kNm, 2.4 m O d.(-)125 Nm, 3.2 m
Draw diagrams of shear force and bending moment for beam and loading shown. Calculate the maximum tensile and compressive stresses in the beam. X=407 N/m Y=2.21 m Z=51,4 mm
Draw the shear and bending moment diagram for the beam.And also show Maximum bending moment Mb=25875lb .ft a tx=9.0ft
Draw the shear and bending moment diagrams for the cantilevered beam below (figure not to scale). Identify the location and magnitude of max shear and bending stresses. 20 in 10 in 10 in 70 in 80 lbs 20 lbs 32.5 lbs
Consider the beam in the picture below: 7kN/m 5kN/m P N/m Section 1 Section 2 Section 3 - L/3 L/3 L/3 %3D Take P = the last four digits of your student number in N/m. If P<250 N/m then take P = 30OON/m instead. Take L = the third digit of your student number, reading left to reight. If this value is zero then take L = 2 Assume: The reaction at the Pin = V pin 47000L+9PL )N 54 The reaction at the Roller = Vroller = 61000L+9PL 54 and that both reactions act vertically upwards. a) Find an expression for the internal moment for Section 1. Show all working and any relevant free body diagrams. b) What is the maximum magnitude of the internal moment for Section 1? Mark sure you prove that the value you calculate is the maximum. c) Find an expression for the internal moment for Section 2. Show all working and any relevant free body diagrams. d) What is the maximum magnitude of the internal moment for Section 2? Mark sure you prove that the value you calculate is the maximum. e) Find an…
Since beam M in the figure is under simple bending moment, A, B and C Calculate the bending stress and shear stress values at the points. for h, b and M Use the values opposite your name in the table below. A M h/4 h/2 Be C. h/2 b(mm) h(mm) M(kNm) 180 380 120
For the beam below, calculate: 1) the support reactions; 2) develop the shear and bending moment equations for each section; 3) draw the bending moment and shear diagrams; 4) calculate the position and the value of the maximum moment and indicate it in the diagram. With Q = 4,2 kN/ma = 3 m
Solid