2 kg of air, which can be modeled as an ideal gas, undergoes an isothermal process from 1.3bar and 2.5m3 to a final pressure of 2bar. The temperature of the system boundary at which heat transfer takes place is 280C. Determine the following. a. The heat transfer for the process in kJ (v b. The entropy produced in kJ/K (

2 kg of air, which can be modeled as an ideal gas, undergoes an isothermal process from 1.3bar and 2.5m3 to a final pressure of 2bar. The temperature of the system boundary at which heat transfer takes place is 280C. Determine the following. a. The heat transfer for the process in kJ (v b. The entropy produced in kJ/K (

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A closed, rigid tank is filled with water. Initially, the tank holds 1.0 lb of saturated vapor and 7.0 lb of saturated liquid, each at 212°F. The water is heated until the tank contains only saturated vapor. Kinetic and potential energy effects can be ignored. Determine the volume of the tank, in ft°, the temperature at the final state, in °F, and the heat transfer, in Btu.
Nitrogen undergoes an adiabatic process, the pressure volume relationship given as p = (5/V)+1.5 where is in bar and V is in m³. During the process the volume changes from 1.5 x 108 mm3 to 0.05 m³ and the system takes 45 kJ of heat. Determine (i) Work done (i) Work done (ii) Change in internal energy (iii) Final pressure of the gas, if the initial pressure is 1 bar (iv) Final temperature of gas, if the initial temperature is 80°C (v) mass (vi) Change in enthalpy. Gas Molecular weight (М) (kJ/kg K) (kJ/kg K) Air 28.97 1.005 0.718 Oxygen Nitrogen Hydrogen Carbon monoxide 32 0.920 0.660 28 1.046 0.754 2 14.40 10.40 28 1.046 0.754
A closed, rigid tank is filled with water. Initially, the tank holds 0.8 lb of saturated vapor and 5.0 lb of saturated liquid, each at 212°F. The water is heated until the tank contains only saturated vapor. Kinetic and potential energy effects can be ignored. Determine the volume of the tank, in ft³, the temperature at the final state, in °F, and the heat transfer, in Btu.
3.24
A closed, rigid tank contains 1.50 kg of water, initially a two phase liquid-vapor mixture at T₁ = 90°C. Heat transfer occurs until the tank contains only saturated vapor at T₂ = 120°C. Determine the initial pressure, p₁, in kPa, and the heat transfer for the process, in kJ.
Water contained in a piston-cylinder assembly, initially at 300°F, a quality of 50%, and a volume of 6 ft°, is heated at constant temperature to saturated vapor. If the rate of heat transfer is 0.2 Btu/s, determine the time, in min, for this process of the water to occur.
Three kilograms of water at 35 degrees Celsius are placed in a piston under 4.335MPa (State 1). Heat isadded to the water at constant pressure until the piston reaches a stop at a total volume of 0.55 m3 (State 2). Most heat is added at constant volume until the temperature of water reaches 425 degrees Celsius (State 3). Determine (a) the quality of fluid and the mass of the vapor at State 2, and (b) the pressure of the fluid at State 3.
A piston-cylinder assembly contains 2 lb of water, initially at 100 lbf/in.² and 400°F. The water undergoes two processes in series: a constant-pressure process followed by a constant volume process. At the end of the constant-volume process, the temperature is 300°F and the water is a two-phase liquid-vapor mixture with a quality of 60%. Neglect kinetic and potential energy effects. Determine the work and heat transfer for each process, all in Btu. Part A Determine the work for the constant-pressure process, in Btu. W12= i Save for Later Btu Attempts: 0 of 4 used Submit Answer
A closed, rigid tank is filled with 0.02 lb of water, initially at 120°F and a quality of 50%. The water receives 8 Btu by heat transfer. Determine the temperature, in °F, pressure, in lbf/in.2, and quality of the water at its final state.
Five kg of water is contained in a piston–cylinder assembly, initially at 5 bar and 300°C. The water is slowly heated at constant pressure to a final state. The heat transfer for the process is 3260 kJ and kinetic and potential energy effects are negligible.Determine the final volume, in m3, and the work for the process, in kJ.
pls answer the given
A piston-cylinder assembly contains 2 lb of water, initially at 100 lbf/in.² and 400°F. The water undergoes two processes in series: a constant-pressure process followed by a constant volume process. At the end of the constant-volume process, the temperature is 300°F and the water is a two-phase liquid-vapor mixture with a quality of 60%. Neglect kinetic and potential energy effects. Determine the work and heat transfer for each process, all in Btu. Part A Determine the work for the constant-pressure process, in Btu. W12-38.05 Your answer is correct. Hint Part B Your answer is correct. Determine the heat transfer for the constant-pressure process, in Btu. Q12--300.366 Part C Hint W23- Btu Determine the work for the constant volume process, in Btu. Save for Later Btu Btu Attempts: 2 of 4 used Attempts: 1 of 4 used Attempts: 0 of 4 used Submit Answer Part D The parts of this question must be completed in order. This part will be available when you complete the part above.