2) How many moles of methylammonium chloride (CH;NH;CI) are needed to prepare a buffer that is pH 9.64 and contains 0.15 moles methylamine (CH;NH2)? pK», CH;NH2 =3.36 *Show calculations!*

2) How many moles of methylammonium chloride (CH;NH;CI) are needed to prepare a buffer that is pH 9.64 and contains 0.15 moles methylamine (CH;NH2)? pK», CH;NH2 =3.36 Show calculations!

Chemical Principles in the Laboratory

11th Edition

ISBN:9781305264434

Author:Emil Slowinski, Wayne C. Wolsey, Robert Rossi

Publisher:Emil Slowinski, Wayne C. Wolsey, Robert Rossi

Chapter25: Ph Measurements-buffers And Their Properties

Section: Chapter Questions

Problem 5ASA

See similar textbooks

Similar questions

What mass of NH4Cl must be added to 0.750 L of a 0.100-M solution of NH3 to give a buffer solution with a pH of 9.26? (Him: Assume a negligible change in volume as the solid is added.)
Which of these combinations is the best to buffer the pH at approximately 9? Explain your choice. CH3COOH/NaCH3COO HCl/NaCl NH3/NH4Cl
Each symbol in the box below represents a mole of a component in one liter of a buffer solution; represents the anion (X-), = the weak acid (HX), = H+, and =OH. Water molecules and the few H+ and OH- ions from the dissociation of HX and X- are not shown. The box contains 10 mol of a weak acid, , in a liter of solution. Show what happens upon (a) the addition of 2 mol of OH- (2 ). (b) the addition of 5 mol of OH- (5 ). (c) the addition of 10 mol of OH- (10 ). (d) the addition of 12 mol of OH- (12 ). Which addition (a)-(d) represents neutralization halfway to the equivalence point?
8-71 Explain why you do not need to know the chemical formula of a buffer compound to use it.
You want to make a buffer with a pH of 10.00 from NH4+/NH3. (a) What must the [ NH4+ ]/[ NH3 ]ratio be? (b) How many moles of NH4Cl must be added to 465 mL of an aqueous solution of 1.24 M NH3 to give this pH? (c) How many milliliters of 0.236 M NH3 must be added to 2.08 g of NH4Cl to give this pH? (d) What volume of 0.499 M NH3 must be added to 395 mL, of 0.109 M NH4Cl to give this pH?
A good buffer generally contains relatively equal concentrations of weak acid and conjugate base. If you wanted to buffer a solution at pH = 4.00 or pH = 10.00, how would you decide which weak acidconjugate base or weak baseconjugate acid pair to use? The second characteristic of a good buffer is good buffering capacity. What is the capacity of a buffer? How do the following buffers differ in capacity? How do they differ in pH? 0.01 M acetic acid/0.01 M sodium acetate 0.1 M acetic acid/0.1 M sodium acetate 1.0 M acetic acid/1.0 M sodium acetate
Sketch the titration curve for a weak acid titrated by a strong base. When performing calculations concerning weak acidstrong base titrations, the general two-slep procedure is to solve a stoichiometry problem first, then to solve an equilibrium problem to determine the pH. What reaction takes place in the stoichiometry part of the problem? What is assumed about this reaction? At the various points in your titration curve, list the major species present after the strong base (NaOH, for example) reacts to completion with the weak acid, HA. What equilibrium problem would you solve at the various points in your titration curve to calculate the pH? Why is pH 7.0 at the equivalence point of a weak acid-strong base titration? Does the pH at the halfway point to equivalence have to be less than 7.0? What does the pH at the halfway point equal? Compare and contrast the titration curves for a strong acidstrong base titration and a weak acidstrong base titration.
A friend asks the following: Consider a buffered solution made up of the weak acid HA and its salt NaA. If a strong base like NaOH is added, the HA reacts with the OH to form A. Thus the amount of acid (HA) is decreased, and the amount of base (A) is increased. Analogously, adding HCI to the buffered solution forms more of the acid (HA) by reacting with the base (A). Thus how can we claim that a buffered solution resists changes in the pH of the solution? How would you explain buffering to this friend?
You have 0.10-mol samples of three acids identified simply as HX, HY, and HZ. For each acid, you make up 0.10 M solutions by adding sufficient water to each of the acid samples. When you measure the pH of these samples, you find that the pH of HX is greater than the pH of HY, which in turn is greater than the pH of HZ. a Which of the acids is the least ionized in its solution? b Which acid has the largest Kd?
Mixing together solutions of acetic acid and sodium hydroxide can make a buffered solution. Explain. How does the amount of each solution added change the effectiveness of the buffer?
Metacresol purple is an indicator that changes from yellow to purple at pH 8.2. (a) What is Ka for this indicator? (b) What is its pH range? (c) What is the color of a solution with pH 9.0 and a few drops of metacresol purple?
The species called glacial acetic acid is 98% acetic acid by mass (d=1.0542g/mL). What volume of glacial acetic acid must be added to 100.0 mL of 1.25 M NaOH to give a buffer with a pH of 4.20?