2 Determine the x and y components of reaction at A using scalar notation. 1 Determine the y component of reaction at Busing scalar Consider the truss shown in (Figure 1). Suppose that F1 =7 kN F2= 8 kN and F3 = 9 kN. notation.

2 Determine the x and y components of reaction at A using scalar notation. 1 Determine the y component of reaction at Busing scalar Consider the truss shown in (Figure 1). Suppose that F1 =7 kN F2= 8 kN and F3 = 9 kN. notation.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure Q5a shows a truss structure in static equilibrium that is simply supported at A and C. Calculate the reaction forces RA and RC when subjected to vertical loads of 50 kN, 25 kN and 15 kN at nodes D, E & C, respectively.
For the statically indeterminate frame shown in Figure 2, use the moment distribution methodto determine the moments at each joint and support. The members are fixed connected at the supports and joints. EI is the same for each member. Suppose that w = 18 kN/m, P1 = 3x kN,and P2 = 22.x kN. Then draw the SFD and BMD. x=9
4
please i need her solving with using the formulas attached below of pin joint linkage
Part B: The Steel beam in Figure b is supported by a ball and socket at D and supported by separate cables at B. If the tension in cable BA and BC is 7500N and 4500N, respectively, determine: a) The components of the i, j, and k components of the resultant force at point B using unit vector notation. b) Assume the mass of the beam is concentrated mid-span, calculate the mass of the beam. 1500 mm A 10000 mm 3000 mm 550 mm B 1650 mm NE
4. Consider the truss shown in the Figure 6 below: 250 KN C 100 KN 450 450 5m Figure 6 a. Calculate the reactions at joints A and B b. Using the method of joints, calculate the forces in members AB, AC and BC. с. State if the forces are in tension or compression
PART 1 Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 m, b=2.0 m, PB = 2 kN, PC = 2 kN, and MB = 20 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. IMAGE* Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) IMAGE* PART 2 Determine the shear force acting at each of the following locations:(a) x = 0+ m (i.e., just to the right of fixed support A)(b) x = 3.5– m (i.e., just to the left of B)(c) x = 3.5+ m (i.e., just to the right of B)(d) x = 5.5– m (i.e., just to the left of C)When entering your answers, use the shear force sign convention.Answer:(a) V = ? kN.(b) V = ? kN.(c) V = ? kN.(d) V = ? kN. PART 3…
For the truss, which shows the reactions found at the supports at A and E, answer the following: a)Find the member forces at A and B using the method of joints. b)Find the member forces of CD, GD, and GF using the method of sections. (ps. this question is from an architectural structures class, I am struggling to begin)
The figure shows a uniform beam of mass m pivoted at its lower end, with a horizontal spring attached between its top end and a vertical wall. The beam makes an angle e with the horizontal. (a) Find an expression for the distance d the spring is stretched from equilibrium. (Use any variable or symbol stated above along with the following as necessary: k and g.) d = (b) Find expressions for the components of the force exerted by the pivot on the beam. (Use the following as necessary: m, k, g, and 0. Assume the positive x-direction is to the right and the positive y direction is upward.) Ry- Ry=
For the following frame, beam or truss, calculate the reactions and the M, V, N diagrams. 15 TIMN 45° 5 45° 30 25 5 1.5
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 m, b=2.5 m, PB = 4 kN, PC = 4 kN, and MB = 60 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.)Answers: Ay = kN, MA = kN-m.
2D truss system below has 5 elements and 4 joints. The truss system is roller supported at joint 1 and pin supported at joint 3. Calculate all member forces of the truss system using the method of joints! Discuss your results! Assume a = 20 ft and P = 8 kips. Perform your calculations on a blank paper using the Given, Find, Analyze layout and draw free-body diagram to describe 2D systems