2) Design a chain link (meaning find its diameter) made out of a ductile cast iron which needs to operate in a furnace that is used to fire ceramic bricks. The chain will be used for five years at 600°C with an applied load of 5000 lbs. Below is a diagram of the chain link and the Larson-Miller parameter graph for this particular cast iron. Be sure to use the specific equation for the Larson-Miller parameter provided on the x-axis of the graph. Furthermore, for your calculations assume a Safety Factor of 2.

2) Design a chain link (meaning find its diameter) made out of a ductile cast iron which needs to operate in a furnace that is used to fire ceramic bricks. The chain will be used for five years at 600°C with an applied load of 5000 lbs. Below is a diagram of the chain link and the Larson-Miller parameter graph for this particular cast iron. Be sure to use the specific equation for the Larson-Miller parameter provided on the x-axis of the graph. Furthermore, for your calculations assume a Safety Factor of 2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Using the trial function uh (x) = a sin(x) and weighting function wh (x) = b sin(x) find an…

Q: Which of the following statements is NOT correct: Delaunay triangulation method is a criterion for…

A: This question is based on the concept of Delaunay triangulation method

Q: i want a displacement and stress equations and mak calculation

A: From the problem, we have the following given values:Young's modulus (E) = 30 x 106…

Q: Question: Consider the following thermal system. The input is T in, and the output is the…

A: Given : To find : State space model

Q: Three strings, attached to the sides of a rectangular frame, are tied together by a knot as shown in…

Q: Concrete is a commonly used construction material. One of its deficiencies is a relative weakness…

A: to find:the stress in the steel and in concrete.given:the side of a square member of concrete is the…

Q: am able to find the first row and the first column of by hand. However, When I do the 2nd row and…

Q: A material has the following properties: density p = 8932 kg/m³, specific heat cp = 1.17 x 10-4…

Q: conductivity

Q: A metal rod, made from metal 1, with a length of 28.0 cm expands by 6.80x10 2 cm when its…

A: Solution:

Q: anding&COL a. Determine the x and y coordinates of the center of mass. Center of mass (x, y) = (…

Q: 62. •A 5-kg object is constrained to move along a straight line. Its initial speed is 12 m/s in one…

Q: Using the trial function u¹(x) = a sin(x) and weighting function w¹(x) = b sin(x) find an…

Q: A composite wall is made up of 10 cm of common brick against 15cm of concrete with 1.5 cm of plaster…

Q: The prime characteristics of the MATLAB program should be: 1. The MATLAB code should show clearly…

Question

2) Design a chain link (meaning find its diameter) made out of a ductile cast iron which
needs to operate in a furnace that is used to fire ceramic bricks. The chain will be used
for five years at 600°C with an applied load of 5000 lbs. Below is a diagram of the chain
link and the Larson-Miller parameter graph for this particular cast iron. Be sure to use
the specific equation for the Larson-Miller parameter provided on the x-axis of the
graph. Furthermore, for your calculations assume a Safety Factor of 2.
Stress (psi)
20,000
10,000
8,000
6,000
4,000
2,000
1,000
32 34 36
Larson-Miller parameter =
30
38 40 42
(36+0.78 ln 1)
T(K)
1000
1200
dis
SH
ER

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step 4 Final-Answer:-

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Fick’s Law of Diffusion and Mass Transfer

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Dtes 6) Take a look at the picture below. Initially the system is at rest. The spring is activated and sends the mass moving with tangential speed "v" and the disk rotating with angular velocity "w". Find expressions for these parameters in terms of the variables given. Final I nitind At Rest Dişk Rolutes Sprivag: compressx a mass と szring Cons & ingetid velocty muss Rotafiond ふnertiu ofDk
I am trying to find a Direction Cosine Matrix (DCM) for the Euler angle body 1-2-3 sequence. I tried making my own function and using the MATLAB function, but the result is a matrix that is transpose of each other. I mean that transpose(EA123toDCM) = E123toDCM. Why is that? Also, for the E123toDCM line, I am using the sequence 'ZYX'. Is that correct or should it be 'XYZ'? I know that that for a DCM of sequence 1-2-3 = R3(theta1)*R2(theta2)*R1(theta3). Is ZYX sequence the same as a 1-2-3 sequence? EA = [pi/3; -pi/4; -pi/6];EA123toDCM = EA123DCM(EA) E123toDCM = angle2dcm(EA(1,1), EA(2,1), EA(3,1), 'ZYX') function [R] = EA123DCM(EA) theta1 = EA(1,1); theta2 = EA(2,1); theta3 = EA(3,1); R1 = @(a)[1 0 0 ; 0 cos(a) -sin(a); 0 sin(a) cos(a)]; R2 = @(a)[cos(a) 0 sin(a) ; 0 1 0 ; -sin(a) 0 cos(a)]; R3 = @(a)[ cos(a) -sin(a) 0; sin(a) cos(a) 0;…
Question 1b
The following figure shows a coffee thermos as a lumped thermal system. Derive the symbolic expression using the given parameters for the temperature change rate of the coffee dT/dt (10 Ambient Temperature Ta Thermos Thickness L Surface area A Conductivity k Connectivity with air h₂ Coffee Temperature T Thermal capacitance C Connectivity with the thermos h₁
4
You have a 1-D steady-state conduction problem, constant thermal properties, with energy generation q_dot. The material is 4.0 cm thick and has a constant thermal conductivity of k = 65.0 (W/m-k). The temperature distribution within the object is: T(x) = a + bx^2 a = 100 Celcius b = -1000 Celcius/m^2 Starting with the Heat Diffusion Equation and using the data given above, determine the following: • Determine the heat generation rate q_dot within the wall. • Determine the heat flux q" at x=0 and at x=L.
1. Suppose you have a 4-foot metal rod, made out of steel which has a thermal conductive factor of a = 4 Assume the temperature on the ends of the rod is always 0 degrees. a) Filling in the numerical parameters mentioned above in the problem, write down the general solution to this heat equation, which should include some unknown coefficients (c,'s), in addition to t's and x's.
Q5
For the following concentration expressions, indicate whether they are uniform or nonuniform and in how many dimensions (OD, 1D, 2D, or 3D), and steady or unsteady. Then for the following control volume and origin, and table of constants, use Excel or Matlab to graph profiles that show how concentration changes within the control volume and over time to a limit of 20 for the following: C(x,0,0,0), C(0,y,0,0), c(0,0,z,0) and C(0,0,0,t). On each graph, show which parameters are held constant, the CV boundaries, and the point where all four plots overlap. 20 C(x=0) 10 a 0.0001 b 0.001 20 0.01 y k 0.1 100 All of the following functions are C(space, time) and so not necessarily just x as suggested. a. C,(x)= C,(x = 0)x exp{- ax} d. C, (x) = C, (x = 0)x exp{-ax}x exp{- by² }x exp{-cz²}x exp{- kt}
The dependence of the tensions t (units: N) in a structure on the external forces f (units: N) follows the linear system Ct=f, where both t and f are 5 by 1 column vectors. The coefficient matrix C has been determined to be [ 11 14 20 -5 -19 ] -5 7 -3 5 -6 4 -5 13 -2 -10 0 0 0 12 -10 0 0 0 0 14 By how many N would the external force f2 need to be decreased (while all other external forces stay the same) in order to decrease the tension t3 by 94 N?
What is the advantage of nitriding? Select all correct answers. Some complex components can be nitride without difficulty. Better wear resistance. Better fatigue resistance. The cheapest method of case hardening. What is the correct definition of plastic deformation? The behavior of a material when its size changes by the addition of heat. The behavior of a material that deforms under load and returns to its original shape when the load is removed. Deformation caused by cleavage, where the material is actually pulled apart across atomic planes within the crystals or along the grain boundaries. The behavior of a material that deforms under load and does not fully return to its original shape when the load is removed.
I do not understand how to read the graph to determine what ? is. Please help me read the graph to understand it. The temperature distribution in a flat slab needs to be studied under the conditions shown in the table. The ? in the table indicates insulated boundary and Q is the distributed heat source. In all cases assume the upper and lower boundaries are insulated. Assume that the units of length, energy, and temperature for the values shown are consistent with a unit value for the coefficient of thermal conductivity.