2 - An aluminum alloy specimen of gauge length 75 mm and of diameter 11.28 mm was subjected to a tensile test, with these results: Load (kN) 2.0 6.5 11.5 13.6 16.0 18.0 19.0 20.5 19.0 Extension (mm) 0 0.012 0.039 0.069 0.080 0.107 0.133 0.158 0.225 0.310 The specimen fractured at a load of 19.0 kN. Determine (a) the modulus of elasticity of the alloy, (b) The percentage elongation. (c) The ductility in term of reduction of area (d) Fracture stress (e) Tensile strength

2 - An aluminum alloy specimen of gauge length 75 mm and of diameter 11.28 mm was subjected to a tensile test, with these results: Load (kN) 2.0 6.5 11.5 13.6 16.0 18.0 19.0 20.5 19.0 Extension (mm) 0 0.012 0.039 0.069 0.080 0.107 0.133 0.158 0.225 0.310 The specimen fractured at a load of 19.0 kN. Determine (a) the modulus of elasticity of the alloy, (b) The percentage elongation. (c) The ductility in term of reduction of area (d) Fracture stress (e) Tensile strength

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The new line of go-karts will have a two-stroke internal combustion engine. The engine generates 35 horsepower at a mean speed of 2000 rpm. The biggest variation in energy per revolution, according to dynamic analysis, is 25% of the mean energy. Design a flywheel to go along with this engine such that the maximum coefficient of speed fluctuation is 0.01. Your design should include all necessary details, such as the design calculations, the appropriate material, detailed dimensions, and manufacturing procedures. Note: As a design problem, there is more than one acceptable solution. One design, though, might be superior to others.
Use the provided data wherever you need. ((transmitted power 0.050 MW, speed 500 rpm, Modulus of Elasticity 220 GPa, Modulus of Rigidity = 70 GPa, Ultimate stress = 620 MPa, Compression stress = 240 MPa, Yield stress = 440 MPa, Shear stress = 120 MPa, F.S. = 4, Bending moment = 0.5 KN m, diameter of rivet 10 mm, pitch 50 mm)). Q2. For the 50 mm shaft shown in figure. 2. If a torque T and moment M are applied to the shaft, use the suitable theories to design the welding joint. Check the whole system. M Figure 2
- You can use Excel or any plotting program not by hand then paste your graph into the solution section. Specify the units. Can you make detailed solution.
Selasi wants a shaft of 5/8 inches diameter to be used in his design project of which he is considering a design factor of 3. He hopes to get the same shaft size or 11/16 inch diameter shaft in the market for his design. So he decided to send his apprentice, Amuzu to the market. Unfortunately, when Amuzu went to the market, there were 1⁄2 inch, 9/16 inch, 3⁄4 inch, and 7/8 inch sizes available in the first shop. Amuzu decided to buy the nearest shaft size in the first shop instead of checking in the other shops where he could have gotten either 5/8 inch or 11/16 inch sizes.a. Discuss the consequences Selasi would incur in his design project if Amuzu had bought 9/16 inch size shaft. b. Discuss the consequences Selasi would incur in his design project if Amuzu had bought 3⁄4 inch size shaft.
can you please find solution for this question
i need the answer quickly
Completely solve and provide the diagram. Box the final answer. Write legibly 2. Water cooled steam condenser receives exhaust from multi-stage turbine at saturation temperature of 40°C. Cooling water is available at 20° at the inlet condition and temperature of water leaving the condenser is at 28°C. What is the LMTD?
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
What are the problems in statically intermediate equations?
Please solve carefully/ellaborately, include the units and draw the diagram. Your works will be appreciated much, Thanks!
I need help with this Please help me
Solve it fast in MS excel with neat diagram of it