I need the answer as soon as possible Use the provided data wherever you need.(transmitted power = 0.050 MW, speed = 500 rpm, Modulus of Elasticity = 220%3DGPa, Modulus of Rigidity = 70 GPa, Ultimate stress = 620 MPa, Compressionstress = 240 MPa, Yield stress = 440 MPa, Shear stress = 120 MPa, F.S. = 4,%3D%3DBending moment = 0.5 KN m, diameter of rivet = 10 mm, pitch = 50 mm)).%3DQ2. For the 50 mm shaft shown in figure. 2. If a torque T and moment M areapplied to the shaft, use the suitable theories to design the welding joint. Chethe whole system.

Answered: Image /qna-images/answer/376c3059-1084-4487-b2f9-c940e72ab176.jpg

Use the provided data wherever you need. (transmitted power = 0.050 MW, speed = 500 rpm, Modulus of Elasticity %3D %3D GPa, Modulus of Rigidity 70 GPa, Ultimate stress = 620 MPa, Compr %3D stress = 240 MPa, Yield stress = 440 MPa, Shear stress = 120 MPa, F.S %3D %3D Bending moment = 0.5 KN m, diameter of rivet = 10 mm, pitch 50 mm)). %3D Q2. For the 50 mm shaft shown in figure. 2. If a torque T and moment applied to the shaft, use the suitable theories to design the welding joint.

Use the provided data wherever you need. (transmitted power = 0.050 MW, speed = 500 rpm, Modulus of Elasticity %3D %3D GPa, Modulus of Rigidity 70 GPa, Ultimate stress = 620 MPa, Compr %3D stress = 240 MPa, Yield stress = 440 MPa, Shear stress = 120 MPa, F.S %3D %3D Bending moment = 0.5 KN m, diameter of rivet = 10 mm, pitch 50 mm)). %3D Q2. For the 50 mm shaft shown in figure. 2. If a torque T and moment applied to the shaft, use the suitable theories to design the welding joint.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Choose the correct answer only as soon as possible please
give a steps by steps explanation of the solution
Just (b) and (c) please!
Please solve the question on the sheet and get a clear picture and submit the picture. thankyou
It is the ability of a liquid to spread out.
Suppose a hippopotamus on land receives 73 units of heat per minute due to solar radiation and 52 units of heat per minute due to infrared radiation. It emits 39 units of infrared radiation and it loses 66 units heat per minute through evaporation. The hippopotamus gains 45 units of heat per minute through its metabolism. Overall, its heat energy is increasing by 50 units per minute (i.e. its temperature is increasing). Delta Hanimal = SR + IRin - IRout ± Hconv ± Hcond - Hevap + Hmet Based on this information we can conclude that the combination of conduction and convection is the animal, and that its current temperature is than the ambient temperature. Select one: a. cooling; warmer b. warming; warmer c. cooling; cooler d. warming; cooler
Could you please explain it in detail. I'm stuck in step 2. Especially T4. I want detailed solution.
can you solve part B without just using those tables to find the answer?
Help me please
Show your complete solution.
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
Simple Machines-Levers, Inclined Planes, and Pulleys Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your Engineering Design journal. Remember to show all work. A lever has an effort arm that is 5 meters long and a resistance (load) arm that is 3.5 meters long. How much effort is needed to lift a 100 Newton weight? 5K i). Draw the figure representing the problem ii). How much effort is needed to lift a 100 Newton weight? iii). What is the Actual Mechanical Advantage 1. 5m i) AOON 5-5m