(2) An 8 bit successive approximation analog to digital converter has full scale reading of 2.55 V and its conversion time for an analog input of 1V is 20µs. The conversion time for a 2V input will be a) 10 μs b) 20 μs c) 40 μs d) 50 μs

(2) An 8 bit successive approximation analog to digital converter has full scale reading of 2.55 V and its conversion time for an analog input of 1V is 20µs. The conversion time for a 2V input will be a) 10 μs b) 20 μs c) 40 μs d) 50 μs

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Which of the following statements are FALSE?

Q: A certain regulator has a percent load regulation of 1%. a) What is the unloaded output voltage if…

A: The rectifier is used to convert the AC signal into the DC signal, so the bridge rectifier is AC to…

Q: If R1 is on, the collector current in the figure is Please select one: a. 0 mA b. 10 mA c. 5.17 mA…

A: Choose the correct option The given circuit is bias BJT circuit as shown in the figure. If R1 is…

Q: A single-phase full-wave transistor rectifier power to motor load. The source feeds voltage is 230V,…

A: In this question, choose the correct option What is average load current Io ? This is single phase…

Q: 5. For each of the following circuits, determine the state of each diode (OFF or ON) and calculate…

A: We can see all the positive terminal of the diodes D1,D2,D3 are connected to different voltage…

Q: A center-tapped FWR circuit have an output dc voltage of 51 V. What is the PIV rating for the diodes…

A: In this question we will find peak inverse voltage rating of diode in center tapped full wave…

Q: The "moderate voltage limiting device" used in ECG circuitry is made of O a None of these Ob 2…

A: As per guidelines given to us we can only provide the solution of first question in multiple type of…

Q: Van=Vmsinat Vòn=Vmsin(at-213) Ven=Vmsin(@t-4/3) T1 T3 T5 Van Vbn ibn L Ven icn R m

Q: Figure Q3 shows a full bridge rectifier circuit. The input line voltage is 120 Vrms and the line…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Show the output voltage for the Vi input voltage in the figure by drawing it along a period (Note:…

A: Given input voltage is

Q: The output for the following clamping circuit is shown below assuming ideal diode calculate the…

Q: 4. a) Determine the output waveform for the following circuit. b) Repeat with the B input held LOW…

A: Given a GATE with the different input waveform To find its output waveform

Q: a successive approximation a/d converter has a resolution of 20 volts . what is it's digital output…

A: Given: Resolution=20 volts Analog input=2.17 volt

Q: The output voltage in rms of a quadrupler is 20 V. Then the minimum PIV rating for each diode is…

Q: Question No.56 A 6-bit ladder D/A converter has a maximum output of 10 V. The output for input…

A: Given a digital to analog converter with, Total number of bit, n = 6. Maximum or full scale voltage,…

Q: Design a Buck Converter with the Following Features. Input Voltage = 50 V Output Voltage = 20 V…

A: Buck Converter: It is a type of DC-DC converter where input voltage is being stepped down to get…

Q: O Inductor Diode Voltage Surce Swilching Device Capactor This DC-to-DC converter has a duty cycle of…

A: Given data: Duty cycle = 33.3% = 0.333 Converter input = 5 V Output voltage = ? The dc-dc…

Q: This is a block diagram of a 4-bit analog to digital converter (A/D). Assume the analog input ranges…

A: The detailed solution is as follows.

Q: 610 510 12V +6V U Ka 510 R3 E 510 IN4007

A: In the circuit the current I1 is flowing through R1 and R3 and current I2 is flowing through R2 and…

Q: following components: DC supply, 1k resistor and a) Ideal diode b) silicon diode Vi (V) Vo (V) 10-…

Q: For the circuit shown in figure determine the output voltage if the input goes from 0 V to 10 V in…

Q: 30°, the average value of output current ir A single-phase full-wave transistor rectifien feeds…

A: In this question we will find single phase full wave rectifier average value of output current for…

Q: In small-signal FETS, the DC voltage sources will be replaced by a O Short circuit Current source…

A: In small signal FETs the DC voltage source is replaced by

Q: In continuous conduction mode, the switching frequency in a DC/DC converter influences which…

A: DC/DC converter:- It is an electronic device that is referred to as a voltage regulator. It is a…

Q: Q2. Calculate the resolutions for the 8-bit, analog-digital converter: Input and output signal…

A: Given, An analog to digital converter has, Voltage range, Vr=10 V (0 to 10 V) Number of bit, n = 8…

Q: Can you help me with this homework problem? Constant voltage drop is Vd=0.7 What is the output volts…

A: The circuit diagram,

Q: A D/A converter has a 14-bit binary input. The output analog voltage range is 0 to 8 V. How many…

A: No. of discrete level of voltage=2n-1No. of discrete level of voltage=214-1No. of discrete level of…

Q: The process that breaks some of the covalent bounds is called: valence doping thermal generation…

A: Doping is the process of adding impurity in intrinsic semiconductor . For example trivalent impurity…

Q: Given Vi=20V peak-to-peak, draw the output wav eform for the said clamper circuit below: Vi Vo 5V…

A: The clamper circuit is shown below: The above clamper circuit is a positively biased clamper…

Q: For a Buck converter you need to calculate what range of duty cycles a controller needs to meet the…

A: Given buck converter, Input voltage = VDC = 80 v to 120 v. Output voltage = V0 = 100 v. Output…

Q: Which of the following is not true about 7905 voltage regulators? It has a minimum input voltage…

A: Not true statement 79 refer to negative output voltages

Q: Exercise 2 For each of the circuits shown below, determine the current I, and the voltage indicated…

A: Diode is unidirectional device. When p side of diode is at higher potential than n side it is…

Q: This is a block diagram of a 4-bit analog to digital converter (A/D). Assume the analog input…

A: The solution can be achieved as follows.

Q: for the circuit shown below: The lower reference threshold 10v vin=5 sinwt -10v 3 kOhm 1 k Ohm

A: A voltage reference is an electrical component or circuit that generates a constant DC…

Q: What is the output (in decimal format) of a 10-bit unipolar A/D converter for the input of 100mV?…

Q: Q2. Consider the following RISC-V loop: (i) (ii) (iii) (iv) (iv) (v) (vi) (vii) DONE: add x12, x11,…

A: Since you have posted a question with multiple subparts, we will solve the first three subparts for…

Q: VCE at B-80 of the silicon transistor shown in the figure below is equal to 150KSL §2KZ VCE 6.58 V

A: The current through 2k ohms resistor is IC+IB. Apply KVL to the output loop.…

Q: Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the…

A: Given Half wave rectifier withLoad current Iload=0.5 AAverage load voltage VL=20 vRipple voltage…

Q: An n-c nmon connguratio (Rp) 61 2.2kN and its transconductance is 3mSiemens. When input voltage is…

A: Given RD = 2.2 Kohm, gm = 3 mS Vi = 200 mV To find output voltage Vo

Q: The diode is considered shorted when both anode and cathode has a) Low resistance b) High…

A: according to question we need to dicuss about diode anode and cathod condition.

Q: To a measurement range of -4 to 6 V, apply a 4-bit analog-to-digital converter. 1- Identify the…

A: Part (1): The circuit diagram for the 4-bit analog-to-digital converter is shown below:

Concept explainers

Digital to Analog Converters

Digital to analog converters are commonly known as DAC, digital analog converter, D2A, or Digital-to-Analog converters. DACs are one of the important devices used in the electronics and electrical domain. DACs are the systems that convert a digital signal into an analog signal, whereas an analog to digital converter or ADC performs the opposite function. Digital signals are those signals that can represent the information or data as a set of discrete values. At a particular instant of time, a digital signal can only take a particular value of data. A digital signal is characterized by two unique values; zeros and ones, or true and false, represented by the Boolean domain. These are also known as binary signals or logic signals. Unlike digital signals, an analog signal is represented by continuous values, where at any time instant, the analog signal is represented by a real number.

Question

(2) An 8 bit successive approximation analog to digital converter has full scale
reading of 2.55 V and its conversion time for an analog input of 1V is 20μs. The
conversion time for a 2V input will be
c) 40 μs
d) 50 μs
a) 10 us
b) 20 μs

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in Parallel. If we connect a lamp load of 2W across this module, choose the correct statement for the above PV Module. (Assume necessary data) a. The output voltage is 0.5V, the output current is 2A b. The output voltage is 0.5V, the output current is 4A c. The output voltage is 2V, the output current is 2A d. The output voltage is 2V, the output current is 4A
Q 1. Determine the output voltage of the Digital-to-Analog Converter (DAC) in Figure 1(a) and plot it in Figure 1(c). The sequence of the four digit binary codes represented by the waveforms in Figure 1(b) are applied to the inputs. A high level is a binary 1and a low level is a binary 0. The least significant binary digit is Do. Do o D₁ 0- 200 ΚΩ www D₂ 0 100 ΚΩ www 50 ΚΩ www 25 ΚΩ D3 0 M 0 -0.25 -0.50 -0.75 -1.00 -1.25 -1.50 -1.75 -2.00 -2.25 -2.50 -2.75 -3.00 -3.25 -3.50 -3.75 (a) Vout (V) R₁ 10 ΚΩ o Vout +5 V Do 0 +5 V D₁ 0 +5 V 0 +5 V 0 D₂ D3 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 non (c) Figure 1 I 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 ||||| (b) Binary input
A five bit digital to analog converter (DAC) has a voltage output range 0-7 V. The resolution of the converter would be Select one: O a. 0.2000V b. 0.5333V c. 1.28571V d. 0.22581V
What is the output (in decimal format) of a 10-bit unipolar A/D converter for the input of 100mV? Assume that the converter uses 5V as a reference voltage for conversion purposes. The converter input range is 0V to 5V. Round your answer to the nearest integer value.
In the counter method A/D converter has an 800-KHz clock and produces an N = 8-bits. Determine the maximum time of conversion, average time of conversion and maximum rate of conversion.
PICmicro A/D converter is configured for 0 to 5v range and is right justified. When analog input voltage of 0.93 volts is applied, what value in decimal will be stored in ADRESL.
Show work/steps: This is a block diagram of a 4-bit analog to digital converter (A/D). Assume the analog input ranges from 0 to 10.0 volts. Fill in the conversion table for the A/D converter. Note that most, but not all, consumer applications use 8-bit A/D and D/A conversions.
Part B Required
(2) An 12 bit successive approximation analog to digital converter has full scale reading of 5 V and its conversion time for an analog input of 2V is 30μs. The conversion time for a 4V input will be b) 20 μs c) 40 μs a) 30 µs d) 50 μs
build an inverting summing amplifier with 2 inputs: a 1 V DC signal anda sine wave with an amplitude of 2 V and 1 kHz frequency.V Simulate for 2 msec
For the model shown below , if the final value of step input is 5 the display output after run this model is: * du/dt Step Deivative Dis play1 infinity none of them
Thank you for the help! This is a block diagram of a 4-bit analog to digital converter (A/D). Assume the analog input ranges from 0 to 10.0 volts. Fill in the conversion table for the A/D converter. Note that most, but not all, consumer applications use 8-bit A/D and D/A conversions.