2 A slight bend prior to a curve means that a 65 km/h curve advisory speed sign is not visible to drivers until 95 m.before the start of the curve. The 85th percentile speed of vehicles on this approach, prior to reaction and braking, has been measured by survey as 88 km/h. If it is assumed that it is desirable for vehicles to slow down to the posted 65 km/h-advisory speed before reaching the curve, what is the required distance to achieve this? Is the available sight distance adequate for this?

2 A slight bend prior to a curve means that a 65 km/h curve advisory speed sign is not visible to drivers until 95 m.before the start of the curve. The 85th percentile speed of vehicles on this approach, prior to reaction and braking, has been measured by survey as 88 km/h. If it is assumed that it is desirable for vehicles to slow down to the posted 65 km/h-advisory speed before reaching the curve, what is the required distance to achieve this? Is the available sight distance adequate for this?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the Greenshields model, the mean free flow speed on a highway facility lane equals 75 mph near zero density, and the jam density is observed to be about 160 veh/mi. Plot the q-k-u curves in proper order. Write down the speed-density, flow-speed, and flow-density equations. Find out the maximum flow, and also mark it on your diagrams. Compute speeds and densities corresponding to a flow of 2,880 veh/h, describing traffic conditions from a driver’s point of view. Calculate average headways, gaps, clearance, and spacing at CASE 1: maximum flow and at CASE 2: jam density. (Suppose the average vehicle length is 17ft)
What will be the non-passing sight distance on a highway for a design speed of 100 kmph when its ascending gradient is 2%? Assume coefficient of friction as 0.7 and brake efficiency as 50%.
A traffic stream is moving at a steady state when entering a mountain grade. Upon entering the grade, the speed, density and flow are 72 km/h, 25 veh/km and 1800 veh/hr respectively. On the grade, a truck drops to a speed of 15 km/h causing traffic to bunch up to a density of 85 veh/km. When the truck pulls over, traffic accelerates to the maximum flow until steady state flow conditions resume. Calculate (a) the flow of traffic behind the truck on the mountain grade (b) the jam density and free flow speed for this road (c) the density and speed when traffic resumes a steady state flow (d) the maximum flow
What will be the non-passing sight distance on a highway for a design speed of 100 kmph when its ascending gradient is 2%? Assume coefficient of friction as 0.7 and brake efficiency as 50%.
I need the answer quickly
Q5 / a. Section road: length = 500 m, average travel time = 90 sec., average running time = 60 sec. and speed limit = 60 Km/hr. Find: fixed and operational delay. Q5 / b. Annual average daily traffic volume = 5000vpd and design hour volume = 750 vpd. Find k – factor and type of roadway. Q5 / c. Four vehicles (5.5, 5.6, 6.4, and 6.5) m long are distributed over length of freeway lane100m. Find Lane occupancy and Density.
Compute the intermediate sight distance for a freeway with a design speed of 80kph if the perception time is assumed to be 2.5 seconds with a skid resistance of 0.70. Assume brake efficiency to be 60%.
Problem 1: A.) Find the angle of banking for a highway curve of 90 meter radius designed to accommodate cars traveling at 160 kph if the coefficient of friction between the tires and the road is 0.60 B.) What is the rated speed of the curve?
The car is traveling at a speed of 77 mi/hr as it approaches point A. Beginning at A, the car decelerates at a constant 7.1 ft/sec2 until it gets to point B, after which its constant rate of decrease of speed is 2.3 ft/sec as it rounds the interchange ramp. Determine the magnitude of the total car acceleration (a) just before it gets to B, (b) just after it passes B, and (c) at point C. 220 B 372' Answers: (a) Just before B, a = ft/sec? (b) Just after B, a = ft/sec2 (c) At C, ft/sec2 =
Find the critical ratio for left turn single lane group 400 veh/h in signalized intersection if the saturation flow rate 2000 veh/h Оа. 5.0 Ob. Non. Ос. 0.3 O d. 0.4