2 A) Normal and shear stresses acting on horizontal and vertical planes at the point is shown in the figure. 1) Determine the principal stresses and the maximum shear stress acting at the point. 2) If the stress element is rotated by 35° clockwise then calculate the normal stresses and shear stress. 12.6 ksi 8.6 ksi 28.8 ksi

2 A) Normal and shear stresses acting on horizontal and vertical planes at the point is shown in the figure. 1) Determine the principal stresses and the maximum shear stress acting at the point. 2) If the stress element is rotated by 35° clockwise then calculate the normal stresses and shear stress. 12.6 ksi 8.6 ksi 28.8 ksi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Figure 1a shows a concrete beam supported by twosolid circular columns. Column AB is made from steeland column CD is made from aluminium, see the stressstrain graphs in Figure 1b. The concrete beam issubjected to the load P as shown in Figure 1a.1. Determine the normal stress in column AB andcolumn CD. 2. Determine the relative change in angle of point Cto A in degrees. Given: P= 100KN L1= 3m L2= 2m L3= 1m dAB= 60mm dCD= 60mm
www The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 60 MPa and Sy = 210 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume 3 = 47° Selle Answer: Sn = Snt = S, 6 ← T 5 S., MPa MPa
The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 100MPA and S, = 245 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 55°. Sy Answer: Sn = MPa Snt = MPa
For the beam shown in Figure, the location of the neutral axis is shown and INA=19.3 x 106mm4 Determine the following What is the maximum shear stress at the neutral axis for this beam? What is the maximum shear stress under the 14kN load at a point 30mm above the bottom of the beam? What is the shear stress at a point 30mm above the bottom of the beam at section C
Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 39 in., b= 33 in., δ1= 0.1625 in., δ2= 0.1 in. Determine the average normal strain along the side AB?in micro rad And answer in right and clear way Determine the average shear strain in the plate at A relative to the horizontal and vertical axes?
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sy-17 MPa, S, - 60 MPa, and Swy- 29 MPa. (a) Draw Mohr's circle for this state of stress. (b) Determine the principal stresses (ơp > op2) and the maximum in-plane shear stress Tmax acting at the point. (c) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g, see Figure 12.15 or Figure 12.16) Say Answers: MPa. Opl = MPa. MPa. Tmax = 0, =
The stresses shown in the figure act at a point on the free surface of a machine component. If o = 22.4 ksi in the direction shown, determine the shear stress Txy at the point. Txy O 14.48 ksi 11.51 ksi O 13.53 ksi O 10.63 ksi O 8.84 ksi 5.0 ksi 24° 2.8 ksi
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, = 220 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 51°. S ↑ Answer: Sn = MPa Snt = MPа
Situation The helical spring shown is axially loaded with a compression force P equal to 5 kN. The mean diameter of the spring is 100 mm and the wire used is 10 mm as indicated in the figure. 1. What is the shear stress at A? 2. What is the shear stress at B? 3. On diameter AB, locate the point of zero stress measured from C. P = 5 kN WW P = 5 kN 100mm A 10mm B
2.18. The stress at a point is defined by the components Oxr = 85 MPa, Oyy= 320 MPa, oz= 100 MPa, Ory =-40 MPa, ơ =50 MPa, ơzx=-20 MPa. Find the three principal stresses, sketch the three Mohr's circles and hence determine the magnitude of the maximum shear stress. yz
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 24.3 ksi, Sy = 2.7 ksi, and Sxy = 4.1 ksi. Assume β=25∘β=25∘. Determine the normal stresses σxσx and σyσy and the shear stress τxyτx⁢y at the point.
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and Sy = 215 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 50°. Sx