2) 50 kVA, 2300 V / 230 V transformer draws 750 W power and 0.5 A current at rated idle primary voltage. If the high voltage side ohmic resistance and reactance are 1.8 ohms and 4 ohms respectively: (a) Idle power factor (b) Primary side inverse EMF value (c) Magnetizing current (d) Calculate the core loss component of the no-load current.

2) 50 kVA, 2300 V / 230 V transformer draws 750 W power and 0.5 A current at rated idle primary voltage. If the high voltage side ohmic resistance and reactance are 1.8 ohms and 4 ohms respectively: (a) Idle power factor (b) Primary side inverse EMF value (c) Magnetizing current (d) Calculate the core loss component of the no-load current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(a) With the aids of sketch and electrical circuit diagram, briefly describe the two types of transformer core construction and their characteristics.
bị (a) Discuss THREE (3) important roles of the instrument current transformer (CT) and voltage transformer (VT) in power system operation.
i need ans within 15 minutes my best wishes ton
Solve for the efficiency at three-eight load at 0.85 power factor of a 10-kVA single phase transformer with the full load copper loss and core losses are 152 and 128 watts, respectively. Determine the secondary terminal voltage when transformer is delivering full load secondary current at 0.95 power factor of a 20-kVA transformer steps down from 6,600 V to 480 v. The resistances of the primary and secondary windings are 12 ohms and 0.08 ohm, respectively.
Consider the three single-phase two-winding transformers shown in Figure. 3. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in A, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a', b', and c' such that VAN is 90° out of phase with V₂'b' for positive sequence. DI H₂ Figure. 3: Three-Winding Transformer
I need the answer as soon as possible
Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer. The no- load voltages in the primary and secondary circuit are 200 and 400 volts, respectively, and at a frequency of 50 Hz. The primary no-load current at a voltage of 200 volts is 0.7 amps and the losses in the core are 70 watts. The resistance and reactance of the primary are 3.2 and 1.25 ohms, respectively. Secondary resistance and reactance 6. 0, 0.07 ohms, respectively. Draw the equivalent circle, showing the values of its elements.
Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).
None
A transformer on no-load has a core-loss of 20 W, draws a current of 1 A (rms) and has an induced emf of 110 V (rms). a) Determine the no-load power factor, b) Determine the core-loss current and magnetizing current. c) Draw the phasor relationship of induced emf, flux and exciting current. d) Calculate the no-load circuit parameters G; and Bm of the transformer. e) Draw the circuit model of transformer on no-load (exciting current). Secondary terminals N1 N2 e2 open Secondary Primary Core (magnetic material)
A 11000/230 V, 150-kVA, 1-phase, 50-Hz transformer has core loss of 1.4 kWand full load copper loss of 1.6 kW. Determine (a) the kVA load for max. efficiency and(b) the value of max. efficiency at unity power factor
YVTA io YVIA Q1) Fill in the blanks by inserting appropriate words/numbers 1- The high value of efficiency in voltage distribution over suspension insulator string is because of ... .... a) grading the insulators. b) using short cross-arms. c) using a guard ring. d) using longer cross-arms. 2- The per unit value of the transformer in the figure below is ... . assume the Spase is 50 MVA and Vese 20 kV in generator side. 50 0.3 P.u 0.2 p.u 20 MVA 20 MVA 25 KV 25 /33KV 3- During the critical disruptive voltage .. a) the conductors are surrounded by a faint violet glow. b) appearing of high hissing noise c) high power losses may happened d) none of the all above 4- If each of the power system component is represented by its equivalent circuit in a diagram, then this diagram is called .......... a) single line diagram b) impedance diagram c) reactance diagram d) power flow diagram. 8.