2-23. Two forces act on the screw eye. If F-600 N, determine the magnitude of the resultant force and the angle if the resultant force is directed vertically upward. 500 N

Q: Strut AB of the 1-m-diameter hatch door exerts aforce of 450 N on point B. Determine the moment of…

A:

Q: Determine the bar forces EF, FG, DI and indicate whether it’s tension and compression

A: Question consist of truss which supported on hinge and roller support . Length of each member and…

Q: 20 m to m A 4000N (5 m 10 m O Determine the Force of member AB. 2 AC. AD.

A:

Q: In every measurement, a 100-meter tape is suspended at the ends under a pull of 15 kg. It is also…

A: W=5kg Pm=15kg To find sag correction

Q: Determine the magnitude of the moment of the force F = {50i - 26 j - 80k} N about the base line BC…

A: Given : F = { 50i - 26j - 80k} N Determine the magnitude of moment of force F ?

Q: Cable AC exerts on beam AB a force P directed along line AC. Knowing that P must have a 350-lb…

A:

Q: 10kN/m 25kN.m 1m 1m Зт 2m

A: Given:- a beam is loaded as shown below

Q: The bridge is constructed as a three-hinged trussed arch. Determine the horizontal and vertical…

A: Solution: Considering the Diagram:

Q: Influence Line: Moving load group Determine the largest (absolute value) of the shear just left of C…

A: Consider the beam diagram;

Q: Problem 2 - The AC link has a uniform rectangular section of 3-mm x 12-mm. Determine the normal…

A: It is given that Link AC has rectangular cross section of 3 mm × 12 mm. We have to calculate the…

Q: A 550 mm B 300 mm 300 mm 300 mm 5 kN. 50 kN

A:

Q: 17. Determine the location of the maximum deflection in ft between supports BC relative to A. 18.…

A: Calculation of deflection using Double integration method

Q: 16-58 The framework consists of two A-36 steel cantilevered beams CD and BA and a simply supported…

A: Consider the free body diagram of the beam BC shown below. Here, VC is the vertical reaction at…

Q: 3 Detemhe the slope at b and the displacoment et pont E for the beam Om lam lom +

A: One another support at B is missing  After considering hinge support at B

Q: The force in member AC Is 10 kN 30 kN C B, 4 m E 40 KN 4m 3 m. 3 m.

A: Consider the figure, Here, T is the tension and C is the compression.

Q: Determine the shear (in kN) in member AB using Portal Method. Input the magnitude only. P=50kN A C…

A: Given data in question  Dimensions  Horizontal point load To find out  Shear force in beam AB

Q: ipe. use mohr's circle

A:

Q: Find the force in member BD. 20 KN 10 KN 4.0000 20 KN 4.0000 3.0000 3.0000

A:

Q: - Determine the moment of the force about point O. s00 N

A:

Q: The force acting on the gear tooth is F = 20 lb.Resolve this force into two components acting along…

A:

Q: Q1) Compute the vertical displacement of point D for the frame shown below. 30 kN 40 kN/m Hinge 10…

A:

Q: 10-2. Determine the moment of inertia about the y axis y- Probs. 10-1/2

A:

Q: 12-6. Determine the elastic curve for the cantilevered beam, which is subjected to the couple momeat…

A: Given data:

Q: 1-49. The railcar lamp is supported by the -in.-diameter pin at A. If the lamp weighs 4 lb, and the…

A:

Q: SKNIM 15 KN- m TI 0.5m 1.5M A,

A:

Q: Р9-2 12 mm The beam is subjected to a shear C125 mm force of V = 25 kN. Determine the shear flow at…

A: Introduction- The beam is a structural component that typically resists loads applied to the beam's…

Q: (12-91. Determine the slope at B and the deflection at point C of the simply supported bcam. E= 200…

A: E = 200 GPa I = 45.5 × 106 mm4  Determine  a. Slope at point-B.  b. Deflection at point-C.  Let's…

Q: Determine the deflection at each of the pulleys C, D, and E. The shaft is made of steel and has a…

A: The beam is symmetrical so the reaction at A and B will same.

Q: 10–43. The shaft is made of A992 steel. It has a diameter of 25 mm and is supported by bearings at A…

A:

Q: Replace the loading on the frame by a single resultant force. Specify where its line of action…

A: First, we draw the free body diagram:-

Q: 242. Determine the horizontal and vertical components f reaction at A, C. and D. Asume the frame is…

A:

Q: Determine the shear and moment of the beam as a function of "x". An internal hinge is placed at…

A:

Q: Replace the loading on the frame by a single resultant force. Specify where its line of action…

A: Assume leftward, upward and anticlockwise moment positive. Calculate the resultant horizontal force:

Q: Determine the shear (in kN) in member AB using Portal Method. Input the magnitude only. P=50KN B…

A: Given data in question  Portal method Horizontal loading  Span distances  To find out  Shear in beam…

Q: 400 N B 4 m D. 600 N -3 m 3 m

A:

Q: Determine the distance d for placement of the load P for equilibrium of the smooth bar in the…

A: The given figure is shown below:

Q: *3-16 The pole is supported by a pin at C and an A-36 steel guy wire AB. If the wire has a diameter…

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.