[1]Two capacitors C1 and C2 = 2C1 are connected in series as shown. If U1 and U2 represent, respectively, the potential energy stored in C1 and C2. which of the following statements is true? O 4U1 = U2 O U1 = 2U2 O U1 = 4U2 %3D O 2U1 = U2

[1]Two capacitors C1 and C2 = 2C1 are connected in series as shown. If U1 and U2 represent, respectively, the potential energy stored in C1 and C2. which of the following statements is true? O 4U1 = U2 O U1 = 2U2 O U1 = 4U2 %3D O 2U1 = U2

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter20: Electric Potential And Capacitance

Section: Chapter Questions

Problem 43P

See similar textbooks

Similar questions

Check Your Understanding Determine the net capacitance C of each network of capacitors shown below. Assume the C1= 1.0 pF, C2=2.0pF, C3=4.0pF, and C4=5.0 pF. Find the charge on each capacitor, assuming there is a potential difference of 12.0 V across each network.
(i) A battery is attached to several different capacitors connected in parallel. Which of the following statements is true? (a) All capacitors have the same charge, and the equivalent capacitance is greater than the capacitance of any of the capacitors in the group, (b) The capacitor with the largest capacitance carries the smallest charge, (c) The potential difference across each capacitor is the same, and the equivalent capacitance is greater than any of the capacitors in the group. (d) The capacitor with the smallest capacitance carries the largest charge. (e) The potential differences across the capacitors are the same only if the capacitances are the same, (ii) The capacitors are reconnected in series, and the combination is again connected to the battery. From the same choices, choose the one that is true.
Check Your Understanding When a cylindrical capacitor is given a charge of 0.500 nC, a potential difference of 20.0 V is measured between the cylinders, (a) What is the capacitance of this system? (b) If the cylinders are 1.0 m long, what is the ratio of their radii?
What If? The two capacitors of Problem 13 (C1 = 5.00 F and C2 = 12.0 F) are now connected in series and to a 9.00-Y battery. Find (a) the equivalent capacitance of the combination. (b) the potential difference across each capacitor, and (c) the charge on each capacitor.
According to UE=12C(V)2 (Eq. 27.3), a greater capacitance means more energy is stored by the capacitor, but according to UE = Q2/2C (Eq. 27.2), a greater capacitance means less energy is stored. How can both of these equations be correct?
Check Your Understanding The potential difference across a 5.0-pF capacitor is 0.40 V. (a) What is the energy stored in this capacitor? (b) The potential difference is now increased to 1.20 V. By what factor is the stored energy increased?
Check Your Understanding When a dielectric is inserted into an isolated and charged capacitor, the stored energy decreases to 33% of its original value, (a) What is the dielectric constant? (b) How does the capacitance change?
A parallel-plate capacitor is charged and then is disconnected from the battery. By what factor does the stored energy change when the plate separation is then doubled? (a) It becomes four times larger. (b) It becomes two times larger. (c) It stays the same. (d) It becomes one-half as large. (e) It becomes one-fourth as large.
(a) Find the equivalent capacitance between points a and b for the group of capacitors connected as shown in Figure P25.12 (page 686). Take C1 = 5.00 F, C2 = 10.0 F, and C3 = 2.00 F. (b) What charge is stored on C3 if the potential difference between points a and b is 60.0 V? Figure P25.12
When a Leyden jar is charged by a hand generator (Fig. 27.1, page 828), the work done by the person turning the crank is stored as electric potential energy in the jar. When a capacitor is charged by a battery, where does the electric potential energy come from?
Suppose that the capacitance of a variable capacitor can be manually changed from 100 pF to 800 pF by turning a dial, connected to one set of plates by a shaft from 0° to 180°. With the dial set at 180° (corresponding to C — 800 pF), the capacitor is connected to a 500-V source. After charging, the capacitor is disconnected from the source, and the dial is turned to 0°. If friction is negligible, how much work is required to turn the dial from 180° to 0°?
If you wish to store a large amount of energy in a capacitor bank, would you connect capacitors in series or parallel? Explain.