1)The simply supported beam is subjected to loads as illustrated in the figure below. a) Draw shear and moment diagrams for the beam b) Determine the location of the centroid /neutral axis and the moment of inertia about the neutral axis. c) Determine the maximum shear stress in the section. d) If a compressive axial load of 100 kN is applied to the ends of the beam through its centroid in addition to the transverse load, what will be the combined critical normal stresses acting on the section. 50 mm 60 kN 8 kN/m 100 kN 100 kN 200 mm 2 m 2 m 2 m 20 mm 300 mm cross section (kN) M (kN.m)

1)The simply supported beam is subjected to loads as illustrated in the figure below. a) Draw shear and moment diagrams for the beam b) Determine the location of the centroid /neutral axis and the moment of inertia about the neutral axis. c) Determine the maximum shear stress in the section. d) If a compressive axial load of 100 kN is applied to the ends of the beam through its centroid in addition to the transverse load, what will be the combined critical normal stresses acting on the section. 50 mm 60 kN 8 kN/m 100 kN 100 kN 200 mm 2 m 2 m 2 m 20 mm 300 mm cross section (kN) M (kN.m)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) Figure 1 shows a fixed end beam with various loads on it. section A-A/B-B/C-C B. section A-A 100mm section C-C 300mm 100mm moment around y- axis 4N.m 150mm dia = 25mm 100mm 200mm section B-B 3000N 4000N 100mm 2000N moment around X-axis 4NLm 1000N Figure 1 a) Determine the combined loadings and draw them on a volume element: Section A-A, Point A on the cross section CS Scanned with CamScanner
1. Calculate reactions at the external supports. 2. Draw the free body diagram. 3. Build the diagrams if shear force and bending moment. (use the section method) 4. Find the diameter of section of the beam. 5. Calculate the maximum Tangential Stress and show the corresponding section. 6. Draw the stress distribution diagram in the most dangerous section of the beam. a (m) 4 b (m) | P (kN) q (kN/m) 1 80 8 A D-? [G] - 100 MPa a q B b P
3) Calculate the transverse shear stress at point P on the cross-section a-a. 's) A beam with square cross section is loaded as shown in the following figure. 2) Calculate the bending stress at point P on the cross-section a-a. 2. 1) Draw the shear force and bending moment diagrams. a-a 100 N/m 125 N 100 Nm N.A. -2 m- -2 m- -2 m- -2 m- 0.4 m- w po W TO
3. a) Develop the shear force and bending moment equations for each section. b) Sketch the shear force and bending moment diagrams for the beam and label the values of shear force and bending moment at the important points. q-2 kN/m A 2 m 2m Figure Q3 M-5 kNm 2m
Given the shear force diagram for a beam in the Figure for Question 1. Assuming there are no concentrated moments applied to the beam:a)Draw the load diagram corresponding to the given shear force diagrm. Identify the magnitude of all forces acting on the beamon the load diagram.b)Draw the bending moment diagram corresponding to the given shear force diagram. Indicate the values of moment on the moment diagram at points A, B, C, D, and E as indicated on the shear diagram.
80 kN.m QUESTION 3. An unsymmetric bending moment of M= M = 80 kN.m is applied on the 30° 30 mm cross-section of an aluminum beam as shown 400 mm in the figure. a) Calculate the maximum tensile and compressive stress values. b) Determine the location of the neutral 200 mm 30 mm axis. 30 mm
The beam is supported at A and B as shown in (Figure 1). Suppose that F = 5 kip and w = 350 lb/ft. Normal Force at point D -5.00 kip. a) Determine the shear force at point D Express your answer in kilopounds to three significant figures. b) Determine the moment at point D. Express your answer in kilopound-feet to three significant figures.
The engine on the lift weighs 900 N. There are pins at points A, B, C, D, E, and G. Note, the pin at D is for the roller only as the attachment between CBD and ED is a weld. a) Determine the internal normal force, shear force and bending moment at points F and H. b) Draw the normal, shear, and bending moment diagrams for the element GAC and element CBD. c) Determine the maximum normal force, shear force and bending moment in this structure. 10° 1250 mm 500 mm | 350 mm F A C 850 mm AREAA 550 mm Н D 700 mm 1500 mm
6. A femur is experiencing a bending moment of 50NM. Assume the femur has the shape of a cylinder, with a radius of 1.5cm. If a cylinder has a 2nd moment of area that can be calculated as 1 = =nR*, and the neutral axis is at the centroid calculate: a) The stress at the centre of the bone b) The maximum compressional stress c) The maximum tensional stress
1: Determine the internal normal force and shear force, and the bending moment in the beam at points C and D. Assume the support at B is a roller. Point C is located just to the right of the 8-kip load. For your explanation section, complete a FBD of the other side of the beam from the version you did to solve the problem. 8 kip 40 kip · ft D B 8 ft – 8 ft 8 ft
Question 5 a) What is the importance of SFD and BMDs for structural engineers? b) For the beam and loading shown in Fig 5-1. i. iii. 2 kN/m -3 m- Figure 5-1 4 kN/m 1.5 m- B Page 5 of 6 Determine the support reactions at A. Draw the shear force diagrams (SFD), clearly indicating the shear force along the span at AB. Draw the bending moment diagrams (BMD), clearly indicating the moments along the span AB.
The 1.5-in diameter solid steel shaft is simply supported at the ends. Two Pulleys are keyed to the shaft where pulley B is of diameter of 4 in and pulley C is of diameter of 8 in. Transverse shear stress needs to be considered. 1) Draw the bending moment diagrams of shaft AD for My and M₂, and indicate the location and the magnitude of the maximum bending moments. 10 in 200 lbf 1000 lbf 10 in 500 lbf 100 lbf 10 in F G E