1m long 1025 steel hold firmly Assume there is a from both ends. It is heated from 20' to 60 °C, Assume it is stress free at 20 °C. b) Assume it is cooled frorm 20°c -20 C. what type and magnitude of stress results? *Hint: E.. = 207 x10 M Pa and d = 11.7 x10 -6 °. steel (025

Q: 2) Find the axial stresses of members BD, CD and CE. Strte if it is tensile or compressive. AM 3m 3w…

A: Let the reaction on support A and H are to be vertically upward. Take moment equilibrium at point A…

Q: Task #1 Develope a MATLAB code that calculates the following using the Finite Element Method. Refer…

A:

Q: QUESTION 3 A 300mm x 100mm channel section is used as a short vertical column. The column is to…

A: given; →dimension ; (b*d)=300mm*100mm→width(b)=300mm→depth(d)=100mm→compressive load (P)=500KN…

Q: 1. A shaft has a diameter of 20 mm, and it is subjected to tensile stress. If the load applied is…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: 10.14. If P = 1000 Kg find the diameter of the elements subjected to compression to avoid buckling.…

A:

Q: Given dĴ 9 D = 400mm T = 300k N'm Inclined plane 0=60 d = 300mm Imax F = 1.5MN 1) Draw a square…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 3 JL -5 OOK F=225,000 lbs 12 ft AISI 1040 Steel F= 225,000 lbs. Temperature changes from 95°F to…

A:

Q: P=4 Strength of Materials t=14 HOME WORK1- Stress Tall = 1.6 Member B is subjected to the…

A:

Q: Please Show work clearly and show free body diagram if possible and be sure with the positive and…

A:

Q: Consider the circular bent rod with điameter 20 mm. The free-end of the bend is subjected to loads…

A: The horizontal force of 400 Newton will generate a bending moment at the section b-b. The vertical…

Q: For the rigid bar shows, find stresses in steel and aluminium. rods due to rise in temperature. of…

A: Since the deformation is greater than the existing gap, thus the net deformation is,

Q: 2) Find the axial stresses of members FD, GD, GE. State if it is tensile or Compressive. E 3m 5o kN…

A: Consider horizontally forward & vertically upward reaction as (+)ve and horizontally backward…

Q: 4. The cross sectional area of each member of the truss is 1.6 in?. Calculate the stresses in…

A: GIVEN DATA - A PLANE TRUSS GIVEN WITH AREA 1.6in2 WE HAVE TO FIND STRESS IN GIVEN MEMBER

Q: Find the rertical if Pis 20KN movement of P Steel Aluminum 4m 2m Im B

A:

Q: 1: Stress in the left rod after its lower end is attached to the st

A:

Q: c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile…

A:

Q: Problem I. In a high-rise building construction, a boom is being used to efficiently transport…

A:

Q: Required Information The part shown is made from AISI 1030 CD steel and is loaded at point C with…

A: Given : material - AISI 1030 CD diameter of bar d = 12 mmNote : Yeild strength for AISI 1030 CD is…

Q: 4. Before the 400-kN load is applied, the rigid each of cross-sectional area 1400 mm2, as shown in…

A:

Q: The rigid bar AB as shown in Figure Q1(a) is supported by a steel road AC having a diameter of 22 mm…

A:

Q: 1. Problem Solving. Woite inside a Box. 1) Find the alliwable safe load p if the stresser in the bar…

A: Stress in bar AB, σAB=60ksi=413.685N/mm2Stress in bar BC, σBC=50ksi=344.738N/mm2Stress in bar CD,…

Q: An aluminum pipe is filled in concrete is subjected to a pure compressive force as shown in the…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: ! Required information A 4.8-ft-long steel wire of 1/4 in. diameter is subjected to a 774-lb tensile…

A: According to the given data D=0.25in L=4.8ft E=-29x106psi P=774lb We need to find  The normal stress

Q: 2 A hollow steel tube with an inside diameter of 110 mm must carry a tensile load of 480 kN.…

A:

Q: 2. (practice problem for Exam 1) Find out the normal stress throughout the bar. - Hint: you should…

A:

Q: 1025 steel hold firmly 60 °C, there is a long It is heated from 20 c to Assume from both ends.…

A: Heat transfer is the form of energy that transfers from one system to another system by virtue of…

Q: HW 1// For the assembly shown in Figure 1. Find: a) Change in temperature so that the two bar just…

A: For steelE=210GPAA=250mm^2For aluminumE=70GPaA=650mm^2

Q: Calculate the maximum stress in the steel ring if a copper ring with a thread diameter of 2000 mm…

A: Given,

Q: A2.2 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: here's a comprehensive explanation of why a bar magnet suspended on a string aligns itself with the…

Q: Answer the questions below for the following system. Young's modulus and Poison's ratio can be taken…

A:

Q: A2.0 kN bar AB carries a load F = 75 kN vertical force at A. The bar is supported by a pin at B and…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: Q 2: A circular rod of 15 mm diameter and 120 mm length, is subjected to 2.5 KN tensile load if the…

A:

Q: 8 The steel column of circular cross section is attached to rigid supports at A and C. Find the…

A:

Q: A metal bar do in diameter and l gage length failed under an axial tensile load of F. The final…

A: Given data

Q: A steel column of hollow circular with length, L is shown in Figure 2. The column cross section has…

A:

Q: Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The diameter of…

A: σBD=200 MPaLbd=48 mmhbd= .95 ma Now link BD σBD=P1AP1=200×π4×482P1=361.911 KNNow taking moment…

Q: End condition total coils wire dia spring index material G squared & ground 14 2.2 mm 10 Hard-drawn…

A: free length l=65mmtotal number of turns nt=14wire diameter  d=2.2mmspring index  c=10G=80GPa=80 x…

Q: 2.) Calculate the torsion constant for the following open and closed sections, which all have a…

A:

Q: Maximum shear stress (Tresca) criterion whether the diameter d is safe using ch

A:

Q: Required information Two solid cylindrical rods AB and BC are welded together at 8 and loaded as…

A:

Q: Consider the bar in Figure 2 loaded as shown. Determine the nodal displacements, stress in each…

A: Given:To find:(a) Nodal displacements.(b) Stress in each element.(c) Support reaction.

Q: B D F 3. A Howe truss is loaded as shown below, P = 32 kN. a) Find the support reactions at A and Н.…

A:

Q: method is used to find stresses on an oblique plane of a member when it is subjected to stresses in…

A: OPTION (B) Mohr's circle

Q: 2 pts) The rigid L-shaped bar show below is supported by pin at A, steel rod at L, and titanium rod…

A: Free Body Diagram:

Q: 2) Tensile strength P is applied to the rectangular cross-section, whose cross-section dimensions…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.