1)For this continuous beam, draw the qualitative and quantitative influence lines of the following using the Muller- Breslau Principle: a) Reaction at B b) Shear at the midspan of beam AB (Hint: use the reaction at B) c) Compute the reaction at B due to a moving concentrated load of 80 kN and a moving uniform load of 10 kN/m acting at span AB only. 2- 0.8 Ih 8m 8m

1)For this continuous beam, draw the qualitative and quantitative influence lines of the following using the Muller- Breslau Principle: a) Reaction at B b) Shear at the midspan of beam AB (Hint: use the reaction at B) c) Compute the reaction at B due to a moving concentrated load of 80 kN and a moving uniform load of 10 kN/m acting at span AB only. 2- 0.8 Ih 8m 8m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For all problems, draw the indicated influence lines. For #1, use both the "unit load method" and the Mueller-Breslau Principle. For #2 through #4, use whatever method you think is easiest, but you must SHOW YOUR WORK. 2. Influence Lines for: RA RC MA Vв k 4 m 4 m
In a fixed beam two internal hinge are provided as shown in figure, the reactive moment A and B are respectively. B: 3m 11₂ D 9m 2 KN/m 1) 9 KNm, 24 kNm 2) 24 kNm, 9 KNm 3) 20kNm,10KNm 4) No reactive moment at A & B 4m
Influence Lines 1 0.5 -0.5 -1 5 10 15 20 25 30 35 40 Location of Load (ft) Determine the reaction at A in kips due to a uniform load of 0.4 kips/ft placed over the whole beam. Recall that areas can be positive or negative. 1. 2. What is the largest possible reaction in kips (absolute value) due to a uniform load of 0.6 kips/ft that can be placed anywhere on the beam? Reaction at A (unitless)
3. For the system shown, a. Determine the equivalent force-couple 300N 200 N 400N - 3m - 4 m system at the base at C. Express the resultants in vector form. (Hint: This is not a static equilibrium problem) b. Write the reaction forces at C support in 2 m 600 Nm vector form | 200 N 7 m
In the figure, draw the influence lines for the reactions Ax and Ay at the left pin support and the bending moment at section 1 located at the face of column AB using ONLY EQUILIBRIUM METHOD. If a uniform live of 0.8 kips/ft is applied on top of the frame, compare the bending moments at section 1 if the live load is only applied on top of the entire span BC, CD, and BD. Discussion the variations and which is the critical loading scenario
For the beam shown in the figure below, draw the influence line for RC, and determine the maximum absolute reaction (negative or positive) at C in kN due to a concentrated live load of 32.8 kN, a uniformly distributed live load of 34 kN/m, and a uniformly distributed dead load of 12 kN /m. Enter absolute value only. A BA 4 m 6 m
For all of the following, draw the requested influence lines and find the worst case for the corresponding response quantity for a uniform load w that can be placed anywhere on the beam. 1. Moment at C, reaction at B, and shear at C. Note that C is just an identifying point, not a hinge. C 10 2. Reaction at A, reaction at B, shear just right of A, and moment at C. Note that C is just an identifying point, not a hinge. A 3. Reaction at A, shear just right of A, and (negative) moment at C. A 10 10'
* For the beam shown , draw the influence lines for (a) Lor the beam shown, draw the influence lines for (a) Reaction ot A, (b) shear just to the right of A,lC7 Moment at A,and (d) Moment at D. Détermine the maximum valuUes of these functions due to (1) concentrated moving loads of 6 KN, and (2) a uniform moving loads of 3kN/m. C A Com 来 3m
Determine the max and min moment reaction (in kN-m) at A (positive counterclockwise) that will be produced due to uniform dead load of 8kN/m, uniform live load of 5 kN/m and concentrated live load of 15 kN. hinge hinge D E 10 m 6 m 3 m 3 m
For the beam shown, it carries a series of concentrated loads moving from left to right. Using influence lines for the beams compute the following: a) max ordinate of the influence line to obtain the max positive moment at point B. b) position of point 1 (145kN) from point A to produce maximum positive moment at B. c) Maximum positive moment at B due to the series of concentrated loads.
The uniform A-36 steel bar in Fig. 4-5a has a diameter of 50 mm and is subjected to the loading shown. Determine the displacement at D. and the displacement of point B relative to C. A 2 m. B 80 KN -1 m (a) 40 kN C - -1.5 m- D 70 kN NBC = 50 KN NCD= 70 KN NBC= 30 kN, 80 kN (b) 40 kN 40 KN 70 kN 70 kN 70 kN
Which of the following gives the reaction at F in the given beam? O 24 kN 10 kN/ m A ĮF 20 kN. m B C D E 12 m12 m1.5 m, 4m 4 m 4 m