1a. Select the best answer and explain why each of the wrong answers are incorrect. Which of the following configurations would allow for a maximum induced current through a 1m segment of wire in the presence of a changing magnetic field? (a) a single circular loop (b) a single square loop (c) a 5-turn circular loop (d) a 5-turn square loop

1a. Select the best answer and explain why each of the wrong answers are incorrect. Which of the following configurations would allow for a maximum induced current through a 1m segment of wire in the presence of a changing magnetic field? (a) a single circular loop (b) a single square loop (c) a 5-turn circular loop (d) a 5-turn square loop

Similar questions

a bar magnet is brought closer to a conducting wire loop with 7Ω of resistance. As a result a uniform 3 A current is induced in the wire. What is the rate at which the external magnetic flux is changing indies the wire loop? Explain the reasoning behind your selection in detail. A) 5 T m2/sB) 10.5 T m2/sC) 21 T m2/sD) 42 T m2/sE) 84 T m2/s
4. The loop in figure is being pushed into the 0.80 T magnetic field at 70 m/s. The resistance of the loop is 0.20 2. What are the direction and the magnitude of the current in the loop? Assume that x = 5.0 cm V • • B ● ● • ● ● • ● ● x ●
A 140-turn circular coil has diameter 4.5 cm. A magnetic field perpendicular to the coil is changing at 0.80 T/s. What is the induced emf in the coil? The symbology is what is killing me. I don't understand the logic steps or where you have to substitute values to determiine the emf.
An inventor designs a model plane that uses the emf that develops across its metal wings as it flies through the earth’s magnetic field to power the plane’s propeller. Will this plane be able to power itself this way? Explain.
5. In the picture shown a diagram labeled ORIGINAL shows a metal loop of wire in a constant magnetic field B that is parallel to the axis of the loop labeled A. Four diagrams are shown labeled #1, #2, #3 and #4. In each diagram a change has been made to the ORIGINAL diagram. For which diagram(s) would an emf be induced in the ring while the change is being made? a. #1 and #2 only b. #3 only c. #1, #3 and #4 d. #1, #2 and #3 e. All of these
a.) a current in the CW direction to enhance the decreasing north magnetic field. b.) a current in the CW direction to enhance the decreasing south magnetic field. c.) a current in the CW direction to oppose the increasing south magnetic field. d.) a current in the CW direction to oppose the increasing north magnetic field. e.) no current in the coil. 7.) A conducting coil is rotated at constant speed in a uniform magnetic field as shown in the figure here. The time required by the loop to make a full rotation is T. The current generated in the coil would increase Side view a.) if the angular speed of the coil increases. b.) if the area of the coil increases. c.) if the strength of the magnetic field increases. d.) All of the above are correct. e.) None of the above are correct. 8.) An RLC circuit has a resonant frequency of fo. When the circuit is driven by an AC voltag source whose frequency is 2fo, which of the following is the most accurate?
The magnetic poles of the coil and the direction of the current shown in the diagram below are: a. The top part of the coil becomes the North magentic pole and the current will flow in the counter clockwise direction looking down at the top of the coil. b. The top part of the coil becomes the North magentic pole and the current will flow in the clockwise direction looking down at the top of the coil c. The top part of the coil becomes the South magentic pole and the current will flow in the counter clockwise direction looking down at the top of the coil d. The top part of the coil becomes the South hmagentic pole and the current will flow in the clockwise direction looking down at the top of the coil
13. You have the apparatus shown in Figure P21.13. A circular metal plate swings past the north pole of a permanent magnet. The metal consists of a series of rings of in- creasing radius. Indicate the direction of the current in one ring (a) as the metal swings down from the left into the magnet- ic field and (b) as the metal swings up to- ward the right out of the magnetic field. Use Lenz's law to justify your answers. Figure P21.13 Metal plate Magnet N
Your classmates have different opinions about why electricity is generated in the generator. Annie claims it’s the movement of the magnets that generate energy, since that’s a form of kinetic energy. Josue claim’s the electricity is generated by the power of the magnets on the outside of the moving center. Which analysis correctly describes how the electricity is generated? (a) The movement of the wire within and the magnets are needed in order for an electrical current to be generated (b) The movement of the center is what generates the electricity, the magnets on the outside don’t need to be there at all (c) The electrical current would be generated if the magnets were incredibly strong and the middle piece did not rotate (d) The placement of magnets on the outside is more important than the movement of the center for the generation of electricity