197100 N/TET (9) 1000 NV/A™ 14. The direction of water flow in pipe is (a) from 1 to 2 (b) from 2 to 1 (c) there is no flow Im Deflection 01m (2)

Q: 2:00-2:35 P2= atm 2 water Di=10 cm D=5cm 80 cm The Pipe reducing section. of the Figure attachol.…

A: P1ρg+Z1-P2ρg-Z2=.8013.6-1Z1=Z2P1ρg-P2ρg=10.08P1-P2=10.08×1000×9.81where…

Q: erature is 40°F, what is the head loss sthf=57.5t, wh

A: Discharge = 2 cfsDiameter of the pipe = 6 inch.Water Temperature = 40 deg FHead Loss in 1000 ft pipe…

Q: 6.52 This spray head discharges water (p = 62.4 lbm/ft³) at a rate of 4 ft³/s. Assuming irrotational…

A: Given data:Discharge (Q)= 4 cfsDiameter of spray head (d)=6 in

Q: Y water is transpor ted at 75°F (v- 10$ for 1500ft .in (l.s)in - dianeter wrought iron horizontal…

A: Given: T = 75 F, D = 1.5 in, Q = 0.1 m3/sec,  We need to determine the pressure drop over 1500 ft…

Q: Q#1: a. Analysis on canal section is carried out by technical team of WASA for a current water flow…

A: Given that:                  Discharge in the canal, Q=8000+2R=8000+2(58)=8116 ft3/sTemperature =…

Q: 9. Connected to an 18-inch water line is a 6-inch horizontal Venturi meter, with a meter coeficient…

A: Given data in question  Diameter of pipe line Diameter of Venturimeter  Coefficient of discharge…

Q: 1. Three pipes of different lengths and diameters connected in series as shown discharges 169…

A:

Q: 22 E Asettling b•sin is dosinnad tohave surface over rate (SUR) of 82 6 m/d - Determine the over all…

A: particle size in mm velocity in cm/sec % particle finer than 0.1 0.107726 90 0.08 0.068945 85…

Q: VII. Data Collection and Analysis Staff Reading (m) Rise Fall RL Remarks Station BS IS FS (m) (m)…

A: To complete the table by rise and fall method

Q: How much flow can intake hose with a 5 sq.cm pass without exceeding the max. The flow (gallons per…

A: A = 5 Sq. cm or Cm2 = 5 × 10-4Vmax = 1.2 m / sCalculate Flow (Q )

Q: a 20 mm diameter steel pipe is used to drain and oil tank (SG-0.88) as shown. The total head loss is…

A:

Q: Critical path, Total float, Free float, Independent float A- 3 B 4 C 3 . DA 2 EB 6 FC 4 GD,E 7 HF,G…

A:

Q: Air duct. d = 10 mm V2 qir dplate =200mm air U= 5om/s Patr = 1.24 k9 m3

A: Manometer It is a device which is used to estimate pressure. A manometer has a U shaped glass tube…

Q: Find in feet the distance the air flows through this duct

A: The objective is to find the total length distance travelled by the air flow in the duct The lengths…

Q: -36"-

A: Solution:- Neutral axis without compression steel, xu=0.87fy×Ast0.36fc×b…

Q: If the municipal water system supplies water at 30 psi and a new one story buildiing is planned. A…

A:

Q: Q1- A/ Define each of the following: (Datume plane, Bench Mark (B.M), Sensitivity of the bubble…

A:

Q: sticity and dimensions of a at the celerity of pressure wav ne pipe diameter is 1.2 m. and d 600 m.…

A: celerity of oressure wave , c =975m/sDiameter of pipe , d = 1.2 m length of pipe , l= 600 m velocity…

Q: The water level in a tank is 34 ft above the ground. A hose is connected to the bottom of the tank…

A:

Q: Water (60°F) is running through Schedule-80 PVC pipe whose size changes gradually from 6-in nominal…

A: To solve this problem, we can use the Bernoulli equation, P + 1/2 * ρ * v² + ρ * g * z =…

Q: Water is flowing at the rate of 300 lit/sec from A to E as shown in the figure. Compute the flow in…

A:

Q: The Manning equation was taken into account to use in: (a) open channel (b) closed conduit (c) pipes…

A: Given:- Manning equation was taken into account to use in-

Q: Air moving at 100 m/s enters a 2-in scheduele 80 steel pipe in an adiabatic flow system. The air is…

A: The relation between maximum conduit length and mach number is:-…

Q: What is the viscosity of SAE 1OW-30 motor oil at 150°F (in ft-/sec)? a. None of the choices Ob.…

A: VISCOSITY(CENTISTOKES) VISCOSITYft2/sec×10-5 10W-30 @104 F                  @212F @104 F…

Q: 1. A pump test is carried out to determine the hydraulic conductivity of a confined aquifer, as…

A: Given:- confined aquifer To find:- equation for k

Q: QUESTION 14 A non-potable water storage tank is at an elevation of 37 feet above the discharge for…

A:

Q: A 60 MLD water treatment plant has 4 mechanical flocculators. The design criteria for each…

A: Detention time=25min Discharge=60MLD

Q: Choose the wrong statement Pipes in parallel have the same head losses Cavitation is undesired event…

A:

Q: (1) Determination of meta-centric height of a boat model. (2) Determination of co-efficient of…

A:

Q: Q2) Water is flowing in three side-by-side pipes of diameter (1.8m) each. The Manning's (n) and the…

A:

Q: • Example: Find the velocity at the pipe center. water D-3" 0.0 (stag.) Hg (S-13.6)

A: To find the velocity at the pipe center Fluid in pipe= WaterFluid in piezometer =…

Q: 3. Compute the flow rate in a gutter section with a design spread of 3 m and cross-slope of…

A:

Q: water enters a horizontal nozzly with diameter 60 mm at 6 m/s and exits to the atmosphere through a…

A: Given: The inlet diameter is 60 mm. The inlet velocity is 6 m/s. The outlet diameter is 40 mm.

Q: A supply pipe is 1500+(Reg.No/100) ft long, water is initially flowing through it at 2 fps, and the…

A:

Q: Find Pressure atA? C. Air Hg Puacum Water 5m A

A: Given data Total water depth = 5m Pressure at air in terms of mercury = 100mm Asked to find the…

Q: Example 3: For the setup shown(Figure below), Draw, ht, he , hp and velocity of flow ? Figure (7a)…

A:

Q: V No.4: AND SAND 20¹ > FIV. 0-361 Ton Cross Section Area: 400 in² K=5.0 x, 10-² cm/sec Find Q Flow…

A:

Q: Calculate the discharge rate of air to the atmosphere from a reservoir at 106 Pa gauge and 20°C…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.