19. An ice cube is placed in a sealed insulated container of hot water at 80°C. After five minutes, the ice cube disappears. Ice Cube Hot Water Water 5 min. Which best describes the change that took place inside the container? Heat energy in the ice cube was dissipated into the hot water. Heat energy in the hot water was reduced by kinetic energy in the ice cube. The total heat energy in the container was reduced by the ice cube. The hot water lost the same amount of heat energy as the ice cube gained.

19. An ice cube is placed in a sealed insulated container of hot water at 80°C. After five minutes, the ice cube disappears. Ice Cube Hot Water Water 5 min. Which best describes the change that took place inside the container? Heat energy in the ice cube was dissipated into the hot water. Heat energy in the hot water was reduced by kinetic energy in the ice cube. The total heat energy in the container was reduced by the ice cube. The hot water lost the same amount of heat energy as the ice cube gained.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A solution is made by mixing 260.0 mL of ethanol initially at 15.5 °C with 260.0 mL of water initially at 23.4 °C. What is the final temperature of the solution assuming that no heat is lost? The density of ethanol is 0.789 g/mL and the density of water is 1.00 g/mL. The specific heat of ethanol is 2.46 J/g.°C and the specific heat of water is 4.184 J/g.°C. Tf = °C
How much heat is needed to raise the temperature of 100.0 grams of water from 25.0°C to 55.0°C? Specific heat capacity of water is 4.184J/g°C. 20920 O 10460 12552 23012
Thirty grams of silicon at 80.0°C is added to 70.0mL of water at 20.0°C. Calculate the final temperature after the two substances are mixed together. The specific heat of water is 4.184J/g°C and the specific heat of silicon is 0.7121 J/g°C.
In a few sentences, relate these energy diagrams (the amount of energy absorbed by hot versus cold water) with the time needed to heat each quantity of water. Does it make sense? Why?
A beaker of hot water with a volume of 43.9 mL has an initial temperature of 94.3 °C. You place a block of metal that has a mass of 43.89 g into the water until the water and metal are at thermal equilibrium. You record that the temperature of the metal increases by 66.56 °C. What is the final temperature °C at thermal equilibrium of the water and block, assuming no heat is lost to the surroundings? The specific heat of the metal block is 0.237 J/g·°C
4. The specific heat of water is quite high at 4.184 J/gC. Explain how life on this planet would be different if the specific heat of water were that of lead at 0.128 J/gC.
A piece of metal with a mass of 59.047 g was heated to 98.0°C and then put into 100.0g of water initially at 23.7°C. The metal and water were allowed to come to an equilibrium temperature, determined to be 27.8°C. Assuming no heat lost to the environment, calculate the specific heat (J/g•°C) of the metal.
A piece of metal weighing 50 grams was heated to 100°C and then dropped into 250 grams of water at 25°C. The metal cooled down and the water became warmer until both were at a temperature of 28.8°C. Calculate the amount of heat absorbed by the water. Assuming that the heat lost by the copper was absorbed by the water, what is the specific heat of the metal? (sH2O = 4.18 J / g °C)
To treat a burn on his hand, a person decides to place an ice cube on the burned skin. The mass of the ice cube is 15.0 g, and its initial temperature is –11.2 °C. The water resulting from the melted ice reaches the temperature of his skin, 29.2 °C. How much heat is absorbed by the ice cube and resulting water? Assume that all of the water remains in the hand. Constants for water can be found in this table.
A sample of copper absorbs 44 kJ of heat, resulting in a temperature rise of 65 °C. Determine the mass (in kg) of the copper sample if the specific heat capacity of copper is 0.385 J/g°C.
You take 246 g of a solid (melting point = 38.9 °C, heat of fusion = 425 J/g) and let it melt in 855 g of water. The water temperature decreases from its initial temperature to 49.5 °C. Ignoring the specific heat of the solid, calculate the initial temperature of the water.
A sample of copper absorbs 44 kJ of heat, resulting in a temperature rise of 65 °C. Determine the mass (in kg) of the copper sample if the specific heat capacity of copper is 0.385 J/g°C.