19-21 Answer it correctly and this is Asap I will rate helpful if fast and perfect 19) To Fix a small bump left on the Face of a workpiece in a lathea) Use a fileb)Ignore itc) Adjust the tool on centre again20) The best tool to use to Chamfer a hole is aa) Chamfer fileb) Counterborec) Countersinkd) Reamer21) A Tap is driven witha) An adjustable Wrenchb) A Combination Wrenchc) A Tap Wrenchd)Pliers

Explanation for Question 19To fix a small bump left on the face of a workpiece in a lathe:Selected…

Answered: 19) To Fix a small bump left on the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Note: I need both answer with clear explanation. Don't copy from other expert answer Urgenttttttt please
the cut length of the ram. 9) The return length of the ram in shaping process is C) Equal. D) Shaping doesn't have a return length. A) Higher. B) Lower. E) Shaping doesn't have a cut length. 10) coatings thicknesses on carbide substrate cutting tools are typically in the range of: A) 1-2 mm. D) 0.4 to 0.8 mm. E) 3 to 10 mm. F) 2 to 10 mm. B) 2 to G) none of the C) 90 to 160 μm. 10 cm. previous.
Tooth breakage on gear is usually a A) A crack B) None of These C) A contact Stress D) A Tensile fatigue
9) To obtain a guide for centering irregular shaped workpiece in the lathe, its face should be laid out with a) parallel lines b) center & center point d) intersecting lines c) perpendicular lines 10) The workpiece is assumed to be already centered when the dial indicator plunger pin touches the whole surface of the workpiece diameter and a) dial indicator b) no deflection on the dial indicator reading c) big deflection on the dial indicator reading d) abrupt change on the dial indicator reading
The taper on the lathe spindle is: A) 1 in 10 B) 1 in 20 C) 1 in 15 D) 1 in 25
solve question 7
Which one of given below is nota chip type? 31 - Aşağıdakilerden hangisi talaş türü değildir? Continuous chip with built-up edge A) yığma kenarlı sürekli talaş Discontinuous chip B) süreksiz talaş Multiple cutting edge chip çoklu kesme kenarı talaşı Serrated chip D) tırtıklı talaş Continuous chip E) sürekli talaş
A. MULTIPLE CHOICE : Select the best answer. Write the letter of the correct answer on the blank provided before each number. 1) The process of aligning the work axis along the axis of the lathe spindle is called a) facing b) straight turning c) centering d) drilling 2) The tool that is provided with a scriber and is used for centering a workpiece held in a chuck a) wiggler b) center drill c) dial indicator d) surface gage a chuck is 3) The instrument that is commonly used for accurate centering of a work piece held in a) wiggler b) dial indicator c) Vernier protractor d) surface gage 4) A method of centering a workpiece without any tool or instrument is a) wiggler b) dial indicator c) chalk d) surface gage 5) The approximate center of the work piece can be obtained by using as guide, is the chuck a) jaws b) concentric ring c) slots d) threads 6) A hexagon is assumed to be centered if the scriber point of the surface gage is touching all its a) flats b) corners c) side d) ends 7) If…
Gear Lapping is an operation: A) for gear reconditioning B) prior to heat treatment C) after heat treatment D) None of the above
8-In lathe, the carriage and tail stock are guided on... a) Same guideways. b) Different guideways. c) Any of the above. d) Not guided on guideways
Which of the following arrangements is least effective in tightening the nut? rod wrench wrench nut nut a) b) rod wrench WIe nch nut nut c) d)
Solve full question I give thumb up?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS