•19 To crack a certain nut in a nutcracker, forces with magnitudes of at least 40 N must act on its shell from both sides. For the nutcracker of Fig. 12-36, with distances L = 12 cm and d = 2.6 cm, what are the force 40 components F1 (perpendicular to the handles) corresponding to that N? L- F \F

Q: Suppose the magnitude of tension force #1 is 25 N and is oriented at 265 degrees. Next, suppose the…

A:

Q: n old streetcar rounds a flat corner of radius 6.00 m, at 21.0 km/h. What angle with the vertical…

A:

Q: In the figure, suppose the length L of the uniform bar is 3.3 m and its weight is 200 N. Also, let…

A: Given  L = 3.3 m  W = 200N  W1(W of block) = 280 N  Angle = 43°  Maximum tension = T = 410 N

Q: 3-1. The members of a truss are pin connected at joint O. Determine the magnitudes of F, and F, for…

A: Solution:-Given thatθ=60°

Q: ngth d= 2.8 m attached to the end of the the other end of the meter stick. hine the tension in the…

A: In the above figure,  "T" is the tension in the cord "Fs" is the friction offered by the…

Q: 3-6. The gusset plate is subjected to the forces of three members. Determine the tension force in…

A:

Q: Compression member AB is used to hold up the 250 x 340-mm rectangular plate. If the compressive…

A:

Q: A strut is attached to a wall at (x, y, z) = (0, 0.0) and extends to a point located at (2, 3, 3) m.…

A:

Q: Macmillan Learning © A person pushing a horizontal, uniformly loaded, 28.05 kg wheelbarrow of length…

A:

Q: Consider a ladder of length 3.30m and mass 18.0kg , leaning against a vertical wall and making an…

A: Mass of the ladder=18kg Mass of the pointer=74kg Coefficient of static friction on the floor=0.65

Q: A uniform beam of length L = 7.25 m and weight 4.65 x 102 N is carried by two workers, Sam and Joe,…

A: The uniform length of the beam,   The weight of the beam,

Q: The two structural members, one of which is in tension and the other in compression, exert the…

A:

Q: (a) Determine the moment of force F about point C. (b) Determine the perpendicular distance (d)…

A: Note: As per the policy, only the first question will be solved. If you want the solution to other…

Q: Summation of Forces Forces are given; Force 1 = 12 N @ 110° Force 2 = 15 N @260° Force 3 = 5 1 - 6…

A: First we have to resolve the forces into Cartesian co-ordinates then simply adding x and y…

Q: A woman climbs a ladder against the side of the building and wants to climb 3/4 of the way to the…

A: Friction  force between building and ladder = 0 But friction force between ladder and ground = f g =…

Q: Q.4) The tensile force in cable AB has a magnitude of 80 lb. The cable is attached to a collar at A…

A:

Q: •19 To crack a certain nut in a nutcracker, forces with magnitudes of at least 40 N must act on its…

A: Given  F = 40N L = 12cm d= 2.6cm To find force ating perpendicular to the Handel's

Q: Problem 3:   A rod of negligible mass is attached to a vertical beam by a hinge at point A and a…

A: Problem 3:  Part (c) Given the values are T = 257.4N, L = 2.81 m, and θ = 20.2°The magnitude of the…

Center of Gravity of a system

The centre of gravity is a property that is based on the geometry of a rigid body or any particle. It is described as an equilibrium point or a hypothetical location where the total weight of the body is concentrated.