180 lbEThe frame shown is loadedby a 180-lb force appliedto member AE. Determinethe force at pin A, thereaction at support B, and4, in.2, in.the contact force at rollerC. Note that there is nofriction at rollers C and4 in. 2 in. 2 in.D.4 in.(10 pts)ReactionValue(left,right,upward/downwardABxByC

Answered: Image /qna-images/answer/52dc493c-e7f4-4848-8477-b3ab831735fa.jpg

180 lb The frame shown is loaded by a 180-lb force applied to member AE. Determine 4, in. the force at pin A, the reaction at support B, and 2, in. the contact force at roller D C. Note that there is no friction at rollers C and 4 in. 4 in. 2 in. 2 in. D. (10 pts) Reaction Value(left,right,upward/downward A Bx By C D

180 lb The frame shown is loaded by a 180-lb force applied to member AE. Determine 4, in. the force at pin A, the reaction at support B, and 2, in. the contact force at roller D C. Note that there is no friction at rollers C and 4 in. 4 in. 2 in. 2 in. D. (10 pts) Reaction Value(left,right,upward/downward A Bx By C D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the force in member BG using a freebody diagram of the rigid member ABC. The force is positive if in tension, negative if in compression. KE E 12' F 12' G 14' 12' 12' 760 Ib Answer: BG = Ib
The rigid pipe is supported by a pin at A and an A-36 steel guy wire BD. 4 ft B 3 ft D 3 ft P C If the wire has a diameter of 0.35 in ., determine how much it stretches when a load of P = 620 lb acts on the pipe. (Figure 1)
*4-84 The rod is made of A-36 steel and has a diameter of 0.25 in. If the springs are compressed 0.5 in. when the tem- perature of the rod is T = 40°F, determine the force in the rod when its temperature is T = 160°F. k= 1000 lb/in. MM- 4ft k = 1000 lb/in. WW
show complete solution ang fbd.
Note:hand written solution should ne avoided.
120 mm 30° F= 210 N y 1. L--x 150 mm The 210N force is applied to the end of body OAB. If e= 55-degree, determine the equivalent force-couple system at the shaft axis O, in Nm.
calcualte the forces in members PQ and QR. USE sections method.
Mechanics. help asap pls
PLEASE DRAW AND LABEL PROPERLY THE FBD. THANK YOU. From the frame loaded as shown. Solve the following: a. Reaction at column A.b. Moment at column A.c. Force at member GH.d. Force at member FE.e. Force at memeber FH.
Given a = 20º and ß = 60º. Determine the moment (1) at A (2) at B F,= 250N F2= 300w A 2m* 4m 3 F3=500N
Determine the force in member DE and in the counters that are acting when P₁ = 7 kips and P₂ = 13 kips. Counters ABA A B P₁ E F The force in DE is The force in counter BE is The force in counter DG is G P₂ 8 ft → kips. ((Click to select) ✓ H kips. ((Click to select) kips. (Click to select) T 6 ft
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. Determine (a) the maximum shear stress in the shaft; and (b) the angle of twist of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. A 4 in. 3.5 in. 3.5 in. ID В C te-4 ft- | 2 ft - 6 ft-