18.- Find Ø and the modulus of the resultant of the vectors shown, knowing that it is on the modulus vector action 90u. R. S=30u Ø=65 90u 12 12 100u 80u
Q: We have a rod made of a certain metal. The rod’s length is L = 1.2 m and has a circular cross…
A: Given L = 1.2 m r = 3.2 mm m = 22 kg d = 2.5 mm we have to find out Young’s modulus for this metal.
Q: A strand of dragline spider silk has a diameter of 6.0 μm, and can support a mass of 2.9 g.…
A: Required : Approximately how many copper wires would it take tosupport the same mass?
Q: Find the Young’s modulus of the wire. (g= 9.81 m/s/s)
A:
Q: 8. Find potential energy per unit volume in compressed bone tissue. Suppose that compressing force…
A: The potential energy stored in a body under compression is, u=UV=σ22YWhere, U=total potential…
Q: A cylindrical steel wire that is 2 m long must stretch no more than 0.25 cm when the applied tensile…
A: The objective of this question is to find the minimum cross-sectional radius of a cylindrical steel…
Q: Asolid copper cube has an edge length of 85.0 cm. How much stress must be applied to the cube to…
A: Here in this Question The Edge length of the copper cube is given to be 85.0 cm and it has been…
Q: Bulk modulus is defined as -P / (ΔV/V). Therefore it can be negative. True or False? a) True b)…
A: The Answer is False.
Q: A 0.800 m-long metal wire has a circular cross section of diameter 0.900 mm. One end of the wire is…
A: Given that, Length of the wire(L)= 0.8 m Diameter (d)= 0.9× 10-³ m So, radius (r)= (0.9×10-³)/2=…
Q: The bonded single lap joint shown below has a width, w = 97 mm and an overlap length, I = 28 mm. =…
A: Given that: Overlap length I = 28 mm Thickness h = 1.1 mmwidth w=97 mmTensile load F=4385 NShear…
Q: Two solid cylindrical rods (1) and (2) are joined together at flange Band loaded, as shown. The…
A: ANSWER :- As in question normal stress is asked and can be calculated as force/area. Area of rod 1…
Q: If the beam attached to a hinge is 4 meters long and weighs 600 Newtons, and the sign weighs 400…
A:
Q: Humans can bite with a force of approximately 796 N. If a human tooth has the Young's modulus of…
A:
Q: A wire of uniform cross sectional area of 0.45 mm is stretched at both ends by a total force of 7O N…
A: Given: Area of cross section of wire is 0.45 mm2. Force acting on the wire is 70 N. Strain produced…
Q: A femur bone of length 30 cm and diameter 2.5 cm is subjected to a compressive tress of 1.5 *10…
A: Given: Stress σ=1.5×108N/m2Young's modulus (Y)=1.5×1010N/mLength L=30cmDiameter d=2.5cm
Q: A solid copper cube has an edge length of 89.6 cm. How much stress must be applied to the cube to…
A:
Q: A solid copper cube has an edge length of 89.3 cm. How much stress must be applied to the cube to…
A:
Q: A solid copper cube has an edge length of 86.9 cm. How much stress must be applied to the cube to…
A:
Q: A 50-N force is applied to a metal rod with a length of 10 m and a cross- sectional area of 1.0 x…
A:
Q: maximum shear = 60 MPa and modulus of rigidity = 77 GPa. Basing from the angle of twist determine…
A:
Q: Three liquids that will not mix are poured into a cylindrical container. The volumes and densities…
A:
Q: Max (mass = 15 kg) is hanging from one end of a 13-m long bungee cord that has its other end fixed…
A:
Q: A 73 m length with a radius of 2.3 m of a cylinder supports a 9.5 x 10 5 kg mass which presses down…
A:
Q: Young's modulus of steel is 1.9 x 10" N/m2.What is the value of the Young's modulus if expressed in…
A: Given data :- Young's modulus of steel in S.I unit is given as Y = 1.9 × 1011…
Q: a metal rod with length 2 m and cross sectional area of 0.002 m2 has a youngs modulus of 20x10^10Pa.…
A:
Q: A solid copper cube has an edge length of 89.9 cm. How much stress must be applied to the cube to…
A: The ratio of volumetric stress with volumetric strain is defined as the bulk modulus. To solve the…
Q: A solid copper cube has an edge length of 81.6 cm. How much stress must be applied to the cube to…
A: Given: L=81.6 cmL'=81.0 cmB=1.4*1011 N/m2
Q: Humans can bite with a force of approximately 810 N. If a human tooth has the Young's modulus of…
A: SOlution: as given F = 810 N E = youngs modulus of bone= A = 1.5 cm2 = 1.5x10-4 m2 L = 1.5 cm =…
Q: A solid copper cube has an edge length of 85.9 cm. How much stress must be applied to the cube to…
A: Given: length of cube l = 85.9 cmfinal length =86cmchange in length ∆l = 86-85.9 = 0.1 cmBulk…
Q: A particular human hair has a Young's modulus of 3.65×109 N/m2 and a diameter of 155 μm. If a 259 g…
A: (a)Write the expression for young’s modulus of the material.
Q: A cubic marshmallow is 3 cm on each side sitting in a room at atmospheric pressure (1.01x105 Pa).…
A: Original side of cube is Pressure is The new side of cube is The pressure at which volume expands is…
Q: How much would the volume of 1.40 cm³ of aluminum on Earth increase if it were placed in changed to…
A: Solution Given dataVolume V=1.40cm3Bulk modulus B=70×109PaPressure on moon less than…
Q: 2- The square plate is deformed into the shape shown by the dashed line. Determine the average…
A:
Q: A spider silk line has a circular cross section. Its diameter is 7.14 micrometers. Its unstretched…
A: When spider changes from the thread, stress will be developed in it , whichbleads yo the expansion…
Q: A wire stretches from 2000 mm to 2005 mm when a 500-N box hangs from one end of it. The wire has a…
A: Original length of wire (L) = 2000 mm = 2 m New length of wire (L') = 2005 mm= 2.005 m Force (F) =…
Q: A 3.5 cm cube of unknown metal has a shear modulus of 5.0x 10°N/m ? absorbed a force of 0.40 N.…
A:
Q: A sphere of copper has a radius of 8.00 cm and is compressed uniformly by a force of 5.00 × 108 N.…
A:
Q: A man with a mass of 72.1 kg stands on one foot. His femur has a cross-sectional area of 8.00 cm2…
A: A) Using the formula for Young's modulus, Y=FLA∆L∆L=FLAY=mgLAY=72.1 kg9.8 m/s20.496 m8.00×10-4…
Q: A solid copper cube has an edge length of 89.9 cm. How much stress must be applied to the cube to…
A:
Q: Humans can bite with a force of approximately 808 N. If a human tooth has the Young's modulus of…
A: Using the equation for Young's Modulus, Y=FLA∆L∆L=FLAY
Q: Question (2) The bracket shown below is to carry a load F = 20 kN acting at an eccentricity of 1.2…
A:
Q: 19. A force of 5000N is applied outwardly to each end of a 5.0-m long rod with a radius of 34.0 cm…
A:
Q: A box Contains 3oresistors. 15 of the resis tors have nominal Values of 1 Ke, lo hae nominal values…
A: Given: 15 resistors of 1kΩ, 10 resistors of 4.7kΩ, 5 resistors of 10kΩ (a) In order to get an…
Trending now
This is a popular solution!
Step by step
Solved in 3 steps with 3 images
