*18-4. A force of P = 60N is applied to the cable, which causes the 200-kg reel to turn since it is resting on the two rollers A and B of the dispenser. Determine the angular velocity of the reel after it has made two revolutions starting from rest. Neglect the mass of the rollers and the mass of the cable. Assume the radius of gyration of the reel about its center axis remains constant at k, = 0.6 m. OG0.75 m Во 0.6 m

*18-4. A force of P = 60N is applied to the cable, which causes the 200-kg reel to turn since it is resting on the two rollers A and B of the dispenser. Determine the angular velocity of the reel after it has made two revolutions starting from rest. Neglect the mass of the rollers and the mass of the cable. Assume the radius of gyration of the reel about its center axis remains constant at k, = 0.6 m. OG0.75 m Во 0.6 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If P = 30 lb, determine the angular acceleration of the 50-lb roller. Assume the roller to be a uniform cylinder and that no slipping occurs
The 18-kg rod AB is pin-connected at A and subjected to a couple moment of M =15 N- m The rod is released from rest when the spring is unstretched at 0 = 30°. As the rod rotates, the spring always remains horizontal, because of the roller support at C. (Figure 1) Determine the rod' s angular velocity, measured clockwise, at the instant 0 = 60°. Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. vec rad/s k = 40 N/m 0.75 m M = 15 N- m
The 10 kg wheel has a radius of gyration about its center O of ko = 300 mm. When the wheel is subjected to the couple moment, it slips as it rolls. Determine the angular acceleration of the wheel and the acceleration of the wheel's center O. The coefficient of kinetic friction between the wheel and the plane is = 0.2. (Figure 1) Figure M 100 N m < 1 of 1 0.4 m Part A Determine the angular acceleration of the wheel. Express your answer to three significant figures and include the appropriate units. α = Submit ■ Part B ao = μÅ X Incorrect; Try Again Value Submit Previous Answers Request Answer Determine the acceleration of the wheel's center O. Express your answer to three significant figures and include the appropriate units. μA Units Value X Incorrect; Try Again Units ? Previous Answers Request Answer ? Units input for part B
SOLVE USING PRINCIPLE OF WORK AND ENERGY
The shown spool has a mass of 450 kg and aradius of gyration Gk=1.2 m. It rests on thesurface of conveyer belt for which the coefficient offriction m= 0.5. If the conveyer acceleratesat2 1.2m / S and the spools rolls without slipping,determine the tension in the wire and the angularacceleration of the spool
The 21-kg uniform thin hollow square plate is pinned at point O, and its side L = 0.5 m. If it is subjected to the constant moment M = 78 N•m and is released from rest from the position as shown, determine its angular velocity w (in rad/s) when it has rotated 45°. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s2. `L MV Your Answer: Answer
17-110. The 15-lb disk rests on the 5-lb plate. A cord is wrapped around the periphery of the disk and attached to the wall at B. If a torque M = 40 lb - ft is applied to the disk, determine the angular acceleration of the disk and the time needed for the end C of the plate to travel 3 ft and strike the wall. Assume the disk does not slip on the plate and the plate rests on the surface at D having a coefficient of kinetic friction of 4, = 0.2. Neglect the mass of the cord. M = 40 lb · ft -3 ft-