175 mm 100 mm B 20° 200 mm A 45 mm

Q: For the frame shown below, determine the magnitudes of the force components that pin C exerts on…

A:

Q: 3. Determine all forces acting on member ABE of the frame shown. Note: D is a frictionless roller.…

A:

Q: Two transmission belts pass over a double-sheaved pulley that is attached to an axle supported by…

A:

Q: 4m Į 20° The Cound for produc B A d 5 kN A crane is used to lift a concrete pipe weighing 5.33 kN…

A: In this problem, we will use the free body diagram to compute the tension in cables AB and AC and to…

Q: E 2.66 A 200-kg crate is to be supported by the rope-and-pulley arrangement shown. Determine the…

A: Given:Mass of the crate, m=200 kg   To Find; Magnitude and Direction of force P.

Q: Q.4. Determine the force F required to hold the system in equilibrium if a torque M of 240 N-m is…

A: Given information: The torque at point D (M) = 240 N-m Let us consider link CD, for the link to be…

Q: The 48-lb load is removed and a 288-lb in. clockwise couple is applied successively at .A. D and E.…

A: Given Applied load 48 lb Replaced moment 288 lb-in To find The components of the reactions at B and…

Q: 4. A5 x8-ft sign of uniform density weighs 270lb and is supported by a ball-and-socket joint at A…

A:

Q: 150 mm 150 mm B 400 mm G 600 mm A

A:

Q: 2. Determine the support reactions for the 2 member frame shown. D is a 4 slug roller and B is a pin…

A: Determine the support reactions for the 2 member frame shown. D is a 4 slug roller and B is a pin…

Q: 4 m 32 m B 16 m 24 m 32 m с An antenna is guyed by three cables as shown. Knowing that the tension…

A:

Q: A small barrel weighing 60 lb is lifted by a pair of tongs as shown. Knowing that a= 5 in., draw the…

A: Given Weight of the barrel = 60 lb a = 5 in To find Free body diagram Force exerted at B, D on tong…

Q: E 2. A force, P of magnitude 90 lb is applied to member ACE, which is supported by a frictionless…

A:

Q: Three cables are used to tether a balloon as shown. Determine the vertical force P exerted by the…

A:

Q: A mechanic uses a crowfoot wrench to loosen a bolt at C . The mechanic holds the socket wrench…

A: Given data Moment at CMC= (360 lb·in)i  Force at C = -(8 lb)i + (4 lb) k   To determine the forces…

Q: A vertical bar AD is attached to two springs of constant k and is in equilibrium in the position…

A: (a) If AB= CD, Assume that the bar deflects about the center with an angle theta as shown below, In…

Q: A 100-lb force directed vertically downward is applied to the toggle vise at C. Knowing that link BD…

A: Consider the free body diagram shown below for the given system.

Q: 1. The 8-ft rod AB and the 6-ft rod BC are hinged at B and supported by cable DE and by…

A: Here, co-ordinates of point D and E will be, D(6,0,6) and E(0,3,0) So, now unit vector in direction…

Q: 2.The lever BCD is hinged at C and is attached to a control rod at B. If P = 200 N, determine (a)…

A: Given data: P = 200 N Need to determine the tension in the rod and reaction at point C.

Q: Knowing that a= 55° and that boom AC exerts on pin C a force directed along line AC , determine (a)…

A: Law of sines:             FACsin35=TBCsin50=1500sin95

Q: The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the…

A: Take the link BCD as shown below, (a) Force in link AB: Calculate length AB, AB=452+2002AB=205 mm…

Q: The press shown is used to emboss a small seal at E. Knowing that the vertical component of the…

A: (a) The free-body diagram of the press is given as,     The reaction at the seal will be a vertical…

Q: 2] The device shown is used to straighten the frames of wrecked autos. Determine the tension of each…

A: It is assumed that Force in member AB and BC required to straighten the frame. Let θ is the angle…

Q: 1.8 m 1.8 m B 2.1 m C 1.8 m. 1.2 m 4 kN

A: