*17-44. The uniform bar of mass m is pin connected to thecollar, which slides along the smooth horizontal rod. If thecollar is given a constant acceleration of a, determinethe bar's inclination angle 0. Neglect the collar's mass.

Draw the FBD for the given problem. Let θ be the angle made by the rod and L be its length. Write…

Answered: *17-44. The uniform bar of mass m is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If P = 30 lb, determine the angular acceleration of the 50-lb roller. Assume the roller to be a uniform cylinder and that no slipping occurs
Example: 18-63. The uniform 80-lb garage door is guided at its ends on the track. If it is released from rest at 0 = 0º, determine the door's angular velocity at the instant = 30°. The spring is originally stretched 1 ft when the door is held open, 0 = 0°. Assume the door can be treated as a thin plate, and there is a spring and pulley system on each of the two sides of the door. Solution: 8 ft A 8 ft B k = 9 lb/ft
The 10 kg wheel has a radius of gyration about its center O of ko = 300 mm. When the wheel is subjected to the couple moment, it slips as it rolls. Determine the angular acceleration of the wheel and the acceleration of the wheel's center O. The coefficient of kinetic friction between the wheel and the plane is = 0.2. (Figure 1) Figure M 100 N m < 1 of 1 0.4 m Part A Determine the angular acceleration of the wheel. Express your answer to three significant figures and include the appropriate units. α = Submit ■ Part B ao = μÅ X Incorrect; Try Again Value Submit Previous Answers Request Answer Determine the acceleration of the wheel's center O. Express your answer to three significant figures and include the appropriate units. μA Units Value X Incorrect; Try Again Units ? Previous Answers Request Answer ? Units input for part B
SOLVE USING PRINCIPLE OF WORK AND ENERGY
The 13.5-lblb disk rests on the 5-lblb plate. A cord is wrapped around the periphery of the disk and attached to the wall at BB. A torque MM = 40 lb⋅ftlb⋅ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at DD having a coefficient of kinetic friction of μk = 0.2. Neglect the mass of the cord Determine the angular acceleration of the disk measured counterclockwise . Determine the time needed for the end CC of the plate to travel 3 ftft and strike the wall.
The 27-kg wheel has a radius of gyration about its center O of ko = 260 mm, and radius r = 0.5 m. When the wheel is subjected to the constant force F = 354 N, applied to the wheel's center axle at an angle = 6°, it starts rolling from rest. Determine the wheel's angular velocity W (in rad/s) after 3.2 seconds if the wheel has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point. Take g = 9.81 m/s². F 0 Your Answer: Answer
The 186-kg wheel has a radius of gyration about its center O of ko = 300 mm, and radius r = 0.4 m. When the wheel is subjected to the constant couple moment M = 92 N.m, it starts rolling from rest. Determine the average friction force that the ground applies to the wheel if it has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper Sl unit. Take g = 9.81 m/s². M Your Answer: units Answer
The homogeneous cylinder A has a mass of 80 kg, and the mss of the hub can be neglected. The magnitude of the variable force P, is in newtons when t is in sec- onds. The velocity of body B changes from 2 m/s downward when t = 0 to 4 m/s downward t = 5 s. Determine the mass of B. Solve all questions using Impulse and Momentum methods
17-110. The 15-lb disk rests on the 5-lb plate. A cord is wrapped around the periphery of the disk and attached to the wall at B. If a torque M = 40 lb - ft is applied to the disk, determine the angular acceleration of the disk and the time needed for the end C of the plate to travel 3 ft and strike the wall. Assume the disk does not slip on the plate and the plate rests on the surface at D having a coefficient of kinetic friction of 4, = 0.2. Neglect the mass of the cord. M = 40 lb · ft -3 ft-
17-73. Cable is unwound from a spool supported on small rollers at A and B by exerting a force T = 300 N on the cable. Compute the time needed to unravel 5 m of cable from the spool if the spool and cable have a total mass of 600 kg and a radius of gyration of ko = 1.2 m. For the calculation, neglect the mass of the cable being unwound and the mass of the rollers at A and B. The rollers turn with no friction. T = 300 N 15 m 0.8 m. 30° B.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

*17-44. The uniform bar of mass m is pin connected to the collar, which slides along the smooth horizontal rod. If the collar is given a constant acceleration of a, determine the bar's inclination angle 0. Neglect the collar's mass.