17. The bracket, which is fastened to a wall by anchor bolts at A and B is loaded by the force P= 120 N and the couple C = 140 N.m. Replace Pand C with (a) an equivalent force-couple system, the force of which acts at A; and (b) two vertical forces, one acting at A and the other at B.

17. The bracket, which is fastened to a wall by anchor bolts at A and B is loaded by the force P= 120 N and the couple C = 140 N.m. Replace Pand C with (a) an equivalent force-couple system, the force of which acts at A; and (b) two vertical forces, one acting at A and the other at B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a…

Q: B D 3 600 lb

Q: Determine

Q: The offset link has a width of w=200mm and a thickness of 40mm. The allowable normal stress is 80…

A: Find the area of the offset link for the link width of 200 mm and thickness of 40 mm.

Q: The frame is subjected to the load of 15 kN which acts on member ABD at D. Determine the required…

Q: A frame ACD is supported by ball-and-socket joints at A and D and by a cable that passes through a…

Q: The wire AB is unstrentched when tetha = 45 degrees. If a load is applied to the bar AC, which…

Q: Determine the force in each member of the truss in terms of the load P. A a D P B ca

Q: Prove if the truss below is determinate, stable, or unstable. P is 3 Kips. Assume A and D as pin…

Q: The A-36 steel wires AB and AD each have a diameter of 2 mm and the unloaded lengths of each wire…

A: Given: The diameter of the wires AB and AD is 2 mm. The length of the wire AC is 1.70 m. The length…

Q: Replace the loading on the frame by a single resultant force. Specify where its line of action…

A: ∑ Fy=RyRY=-400+600-90045+40035=-280N∑ FX=RX RX=90035-40045=220N

Q: The truss shown is used to support the floor deck. The uniform load on deck is 2.5 k/ft . This load…

A: Consider the free body diagram;

Q: Show complete solution. Draw the following structures then classify whether Statically Determinate,…

A: Static indeterminacy is a conjecture that shows the difference between the total number of unknowns…

Q: 2. Determine the resultant R of the three tension forces on the eye bolt. 250N 30° देस của vua 300 N…

A: Reference : Engineering Mechanics, Resultant of three tension forces Given : A eye bolt with number…

Q: 4-43 The center post B of the assembly has an original length of 124.7 mm, whereas posts A and C…

A: The normal stress at A(&C) and B is 189.315 MPa and 21.3675 MPa, respectively.Explanation:From…

Q: 1a/Assume the support at A and B or D are pins

A: The objective of the question is to understand the forces acting on a structure and how they are…

Q: rhombic shape) under the applied force P. Deter connections to be pin joints and set P = 140 lb, L P…

Q: *2-16. Classify each of the structures as static determinate, statically indeterminate, or unstable…

A: To find degree of static indeterminacy

Q: 3-3. If the 5-kg block is suspended from the pulley B and he sag of the cord is d 0.15 m. determine…

Q: (C) Calculate the force in member bd using the principle of superposition for the truss loading…

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

17. The bracket, which is fastened to a wall by anchor bolts at A and B is loaded by the force P= 120 N and
the couple C = 140 N.m. Replace P and C with (a) an equivalent force-couple system, the force of which acts
at A; and (b) two vertical forces, one acting at A and the other at B.
150 mm
- 700 mm-
OA
200 mm
1200 mm

16. Replace the two couples shown by a single equivalent couple.
45
75 N
1.5 m
75 N
45
0.6 m
60 N-m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the force in each member . Indicate whether each member is in tension ( T ) or compressive ( C ).
Determine the magnitude of the pin force at A. Assume W - 620 Ib, a- 4.6 ft, b-3.1 ft,r-8 in. C B W Answer: A- Ib
Determine the force in member CE of the truss below. Indicate as positive if the member is in tension and negative (-) if the member is in compression. Provide the answer in kN G 3 m 1981 A E 1839 B -2 m- ce po C 5 kN -2 m- -2 m- 5 kN D 5 kN
1-7. Determine the resultant internal loading on the cross section through point D of the pliers. There is a pin at A, and the jaws at B are smooth. 20 N 20 N -120 mm- 80 mm 30° 40 mm 15 mm B
Draw the force diagram of pipe ABCDE Determine the magnitude of the concentrated force, F_cd, equivalent to the applied distributed load. Determine the magnitude in terms of T of the resultant of the two tension forces, T_ce and T_cfx-component, Rx: _____Ty-component, Ry: _____Tz-component, Rz: _____T Determine the unit vector for line AD (assume A to D is the positive direction). (component x,y,z) Determine the magnitude of the tension force on cable ECF
presciate it
For the given girders of the frame shown which carries a uniform load of 14.6 kN/m along span GH and HI and a unifoem load of 33.8 kN/m along soan DE and EF Dimensions are given as follows: A=3.7m B=5.9m C=7.5m Using the approximation frames under vertical loads. Compute the value of the absolute moment at reaction B. (kN-m) Answer: 46.7 Need solution
Present your solution and box your final answer
Determine the force in Pin C for the frame shown. Frame comprises three members - AC, AB, and BD. Lengths are in meters. A B C D 20 40 N 12
Show complete solution - Given, Required, Solution.